C- Cofo Is. Aprove bhab? stationary wore front control surface wwwwwwwwwwwwwwwww C-olv Piep Prep P

Q: The composite bar is initially stress-free. Calculate the stress in each material and indicate…

A:

Q: The Fink truss is supported by a hinge at A and by rollers on a 1 to 2 slope at B. The bracing bars…

A:

Q: For the beam and loading shown, determine the vertical reaction at B (Ib) provided that a=199,…

A:

Q: 4. Without using any software, write a G-code programme to produce the part shown in Figure 2. Take…

A: N0 G90 F0.5 S1200 T0101 M03N10 G00 X35 Z2N30 G71 U0.5 R1N35 G71 P36 Q90 U0.05 W0.05N36 G01 X20 Z0N50…

Q: advantages and 5 disadvantages of using trash pumpp

A:

Q: Construct didactic sketches, showing the operating principles of both heat pumps and refrigeration…

A: Refrigerant= HFC-134a High pressure line = 0.8 MPa Low pressure line = -10oC Refrigerant mass flow…

Q: Determine the absolute value of the first moment of the area (in mm) about the indicated x-axis in…

A:

Q: A small cable car is used to transport passengers across a river. If the cable car and its contents…

A: In the given problem, pulley at B is considered to be frictionless, thus tension on both the sides…

Q: 4. A batch of concrete consisted of 200 lbs fine aggregate (sand), 400 lbs coarse aggregate…

A: The volume of a container is commonly considered to represent its capacity or the amount of fluid…

Q: A 10- ft tank contains gas at a pressure of 500 psia, temperature of 85 °F and a weight of 25…

A:

Q: Differentite between enclosure hoods, canopy hoods, and capturing hoods.

A: A capturing hood is a device that channels the outflow of air from an air conditioning system. It…

Q: In two dimensional boundary layer, shear stress was changed linearly from the solid surface toward…

A: For setting (1): (i) Write the expression of displacement thickness. δd=∫0δ1-uUdy

Q: 5-2. The coefficient of friction between the 200-b homogeneous cylinder of Fig. PS-2 and horizontal…

A: The frictional force exerted on cyclinder by the horizontal surface Na=200 lb

Q: An 800 N-m couple is applied to the flywheel as shown. The coefficient of belt friction is 0.20. The…

A: (a) Since the moment is in anti-clockwise direction, the rope is stretched that is attached to the…

Q: Solve for the x-component (in cm) of the centroid if that a=94.2cm, b=107.7cm, and r=42.4cm. Round…

A:

Q: Determine the center of gravity of the following shape. .06 10'-0" 6'-0" 6'-0" 20.0¹ 10'-0" 90°…

A: The center of gravity of the composite area:

Q: If the tension developed in each of the cables must not exceed T (N). Determine the maximum mass of…

A:

Q: D. cutting path d Figure P2.208 and P2.209

A:

Q: According to vapor compression refrigeration cycle, Refrigerant-134a enters the adiabatic compressor…

A:

Q: What is the External flow over flat Plat

A: When a viscous fluid with some velocity come in contact with the flat plate, due to no slip…

Q: What is Stack gas in FGD scrubbing?

A: FGD (Flue gas desulfurization)scrubbing is a method to remove the sulfur dioxide(SO2) from…

Q: 4. Determine the magnitude and coordinate direction angles of the resultant force. ₂-12 kN 25° 50°…

A:

Q: The spool in the given figure weighs 25 N, and its center of gravity is located at the geometric…

A: Given :  The weight of spool =25 N The weight of block =50 N Freebody diagram : Concept used :…

Q: Eliminate the arbitrary constant on the given function : 2x y = cje+ cze %3D

A:

Q: Determine the magnitude of force (kN) in member AC if F=70865 N , a=3.37m , b=1.0 and c=4.28m. Round…

A:

Q: Question 3 All members of the truss have the same length L=3.2 m. Determine the MAGNITUDE (N) of…

A:

Q: 800 lb 600 Ib 20 A 20 20 20- 400 lb 1000 lb Referring to the given truss above, (a) Using the method…

A:

Q: Problem 2: A 4 by 4 – in. w0od – post BC is connected to a 1 – in. diameter steel eye – bar AB to…

A: FAy=513FA ∑Mc=0 7000*5=FA*513*7 FA=13000 lbs      (T) σAB=FAA=13000*4π*12=16552.1 psi ∑Fy=0…

Q: Observe the figure below. Determine the following: a. axial stress on the shank if the load applied…

A:

Q: PROBLEM 2 Plates A, B and C are of the same thickness, 50mm. Pin diameter = 50mm Find the following:…

A: Given:  Two plates A and B at connected to Plate C through a pin as shown in the diagram given in…

Q: (A) Two buses start at the same time towards each other from terminals A and B, 8 km apart. The time…

A: (A) given : for Bus-x : ( A to B) tₓ = 8 minutes = 8*60 sec   for Bus-y : ( B to A) ty = 10 minutes…

Q: provided that a=186, b=101, c=9 and d=6. Round off only on the final answer expressed in 3 decimal…

A:

Q: An airplane takes off as shown following a trajectory described by equation y = Kx, where K 2x10-4…

A:

Q: A 4-pole lap wound armature of a dc generator has 120 slots, 4 conductors per slot. The flux per…

A:

Q: 15 15 25 20 70 LINE OF SIGHT 15 25

A: GIVEN DATA ISOMETRIC VIEW GIVEN WE HAVE TO DRAW ALL THREE VIEWS AS TOP , FRONT AND SIDE

Q: LS HELP ME IDENTIFY THE OBLIQUE, TOP, RIGHT, AND FRONT VIEW THANK YOU!!

A:

Q: Determine the magnitudes of all pin reactions for the frame loaded as shown. Part 1 765 mm Ax 35⁰…

A: