(c) An electronic Pl temperature controller has an output p of 15 mA when the set point equals thenominal process temperature. The controller response to step change in the temperature set point of 3mA is shown below.t(s)0-0+206080Determine the controller gain K, and the integral time.rp (mA)8,06,86.04.43.6

In the problem, the following information was provided:The PI temperature sensor step response is…

Answered: (c) An electronic PI temperature…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A mechanical system is presented as below. There are four simulation graphs for different values for m, b and c tested for a step response. Identify the graph for m=4 kg, b=0.3 N.s/m and k=1 N/m (Hint: you may need to use matlab simulation to find it). m 1.8 1.6 1.4 b ·f(t) Step Response
In a linear finite element model related to bar problem in static equilibrium, as per the finite element model’s sign convention, which one of the following statements is true? Select one: a. If ue1 is negative then node 1 is moving to the right b. If ue1 is positive then node 1 is moving to the left c. If ue2 is negative then node 2 is moving to the left d. If ue2 is positive then node 2 is moving to the left
Which one is the linearized modelling equation of the given system. 5-3Nm Your answer: O 22 + +72= fa(t) O2+6+11r fa(t) O 2+62 +9r= Ja(1)
I need a clear step by step answer please with the simplest method :) Thank you
2- Consider figure represented below: If the number of finished goods () is 10,000, then what is the input ()?
The input and output relationship of a process plant is given by: 3s+1 Y(s) = U(s) s3+9s2+26s+ 24 Identify the correct diagonal canonical form for the process plant system from the list below: (Note: You should select the correct answer number and also provide us with the calculation notes. Remember, all your calculation notes must be attached and uploaded as a separate document. It should be clean and readable with question numbers and their corresponding solution notes. Failure to provide this calculation notes could result in the candidate being awarded zero marks. Also, you may use MATLAB or any other calculation tools to cross-check answers should you wish to). O a. -2 0 0 x = 0 -3 0 x+1|u; y = [2.5 6 8]x 0 0 -4] O b. 4 0 0 x = 0 -3 0 0 -2] -0.31 0 x+ 0.3 u; y = [18 26 9]x [-0.3] O c. 4 0 0 -2.51 x = -3 0x+ u; y = [0 3 1]x 0 0 -21 -5.5 O d. None of the above
Break down how got the answer simply? For period what is as?
3. Consider the mechanical system shown in Fig. 3. Let V3(t) be the input and the acceleration of the mass be the output. Derive the state equations and the output equation using linear graphs and normal trees. V,(t) В m k2 101 k, Figure 3: A mechanical system with an across-variable source
A single degree-of-freedom linear elastic structure was subjected to a series of harmonic excitations, one at a time. The excitations had the same forcing magnitude but different forcing frequency. Forcing frequencies and observed peak steady-state displacements are shown in the graph below. Find the natural period and damping ratio of the structure. Displacement (mm) 60 50 40 30 20 10 0 0 1 2 . 3 4 Forcing frequency, f [Hz] 5 4. 6 7
The rapid progress of engineering design and information technology has caused difficulties in analyzing system reliability. Because of the increased complexity in system reliability structure (component/subsystem interfaces), many unexpected failure modes could occur, and their behaviors are interdependent. At a system’s design and development stage, the main challenge in analyzing a complex system is the failure uncertainty introduced by the incomplete knowledge of the system. This makes it hard to decompose system reliability into subsystem/component reliability in a deterministic manner, such as series or parallel systems. As a result, some common reliability analysis tools such as fault tree (FT) and reliability block diagram (RBD) become inadequate. Do you agree, why or why not? Are there any other approaches to system reliability assessment beside these tools at the early system’s design and development stage (what are these approaches)?

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

(c) An electronic PI temperature controller has an output p of 15 mA when the set point equals the nominal process temperature. The controller response to step change in the temperature set point of 3 mA is shown below. t(s) 0- 0+ 20 60 p (mA) 8,0 6.8 6.0 44