c) A Flyback converter has an input of 332 V from a DC source, operating at 40 kHz with duty cycle approximately 1/3. The rated output is 12 V at 5 A. The circuit operates with continuous inductor current at threshold 1.5 A, and the turn ratio must be an integer. By assuming that all the components are ideal, and capacitor and inductor are operating in steady state : i. Draw the converter circuit.

c) A Flyback converter has an input of 332 V from a DC source, operating at 40 kHz with duty cycle approximately 1/3. The rated output is 12 V at 5 A. The circuit operates with continuous inductor current at threshold 1.5 A, and the turn ratio must be an integer. By assuming that all the components are ideal, and capacitor and inductor are operating in steady state : i. Draw the converter circuit.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The buck converter with resistive load has the input voltage of 30[V], the output voltage of 10[V] (constant), and the switching frequency of 40 [kHz]. If the output average power is 25[W], then determine the size of the inductor such that the minimum inductor current is 25 % of the average inductor current.
A three phase full controlled converter is supplied by a phase voltage Vs=120V, 60 Hz. Consider a resistive load R=10 N. If the RMS value of the output current is equal to 20A and the input Volt Ampere VA = 5000VA, then the output power Po and the power factor would be equal to: Select one: O a. 3000W, 0.7 lagging on O b. 3196.84W, 0.372 lagging Oc 3196.84W, 0.75 lagging O d. 4000W, 0.8 lagging
A DC-DC converter shown below is being utilized for keeping a constant voltage in order to distribute electricity under any environmental condition. The output voltage is kept constant at 28 V while the input source voltage varies between 24 and 32 volt. The variation in the output load current is between 7 A to 10 A. Design the value of CCM inductance if the converter switching frequency is 11 kHz. SWI SW2
A boost converter has an input voltage Vb-5V. The average load current is lo-0SA. The switching frequency is 25 kHz. Suppose that a regulator is added (L=0.15 mH and C-0.22 mF) and that the current is continuous. if the average output voltage is Vo =15V, then the ripple current of the inductor delta) is equal to: Select one: O a. None of these O b.0.89A O C. 1.41A O d. 0.56A
4. A biased clamper is connected to a rectangular AC input with 20V on the positive half cycle and -10V on the negative half cycle. The orientation of the Si diode is the same with Vo while the 5V biasing voltage is in opposite connection. The value of R is 100K ohms while the capacitor is 1 microFarad. Find the voltage across the capacitor. Estimate the amount of time needed to fully discharge the capacitor. Find the magnitude of the output swing. Find the output voltage (Vo) during the negative half cycle. Find the output voltage (Vo) during the positive half cycle. Find the value of the Time Constant (Tau).
A DC chopper has a resistive load of R = 10 2 and an input voltage of V5 = 220 V. When the chopper switch remains in the ON state, its voltage drop is Vch = 2 V. If the duty cycle is 50%, determine its average output voltage Vo
Build an AC/DC dual power supply circuit that draws a 60Vp-p sinusoidal voltage, to provide a dc output voltage of +15 V. Full analysis of voltages and currents should be included. What modifications would you recommend to draw more current while maintaining same output voltage?
Design a buck converter such that the output voltage varies between from 20V to 28Vwhile the input voltage is 40V . The maximum load power is 200Wdc. Assume the switchingfrequency is 15kHz. (a) Design the converter such that it will be in continuous current mode.(b) The capacitor realized output voltage ripple must not be more than 1% at worst case.(c) The inductance realizes CCM at worst case.(d) Select the appropriate switch and other elements...
Please help me
Design a buck converter such that the output voltage varies between from 20V to 28V while the input voltage is 40V. The maximum load power is 200Wde. Assume the switching frequency is 15kHz. (a) Design the converter such that it will be in continuous current mode. (b) The capacitor realized output voltage ripple must not be more than 1% at worst case. (c) The inductance realizes CCM at worst case. (d) Select the appropriate switch and other elements
3. help please
DC DC Converters a) A step-up PWM converter has the following data: V = 8 V, Vo = 24 V, lo = 1.25 A, and f = 200 kHz. Calculate the minimum inductance required for the converter operation in CCM (Continuous Current Mode). Then, determine the required capacitance for the converter. Assume n = 100 %. b) Design a boost SMPS converter to meet the following specifications: V = 80 V, Vo= 400 V, R. = 480 n, f.= 25 kHz, VNOS 1%. Find L, C, minimum inductor current lupin), maximum inductor current tunan), and output power. Then, sketch the inductor voitage and current waveforms for one cycle.