By considering the channel index as 5/3, the setting of an orifice type irrigation outlet to have proportionality is A 0.90 B WRONG 0.67 C 0.30 CORRECT D 0.15

Q: 2.1 In a rectangular channel F, and F, are the Froude numbers corresponding to the alternate depths…

A:

Q: An inlet Warpd transition was used to connect a rectangular flume with a trapezoidal canal as shown…

A:

Q: Question 4 Water flows upwards in a vertical (plane) pipe line of gradually varying cross section…

A: Given- Head difference between point 1 & 2 = 1.5 m, Discharge Q=0.9 m3/s, Diameter at section 1…

Q: A circular conduit is to satisfy the following conditions: Capacity when flowing full is 0.13…

A: The Chezy's formula is given below,

Q: Table 1 shows the data for the network of pipes connecting four reservoirs to a common junction, J.…

A:

Q: Since there is a need to supply more water from reservoir A to reservoir B, it is necessary to lay…

A: Solution f = 0.25 L =6000 m Q = 0.65 m3/s Applying the Bernoulli's equation on the free water…

Q: In a furrow irrigation system, the following information is given Length of a furrow = 200 m •…

A:

Q: Question-A The channel index at irrigation outlet is 5/3. Find the value of setting for an orifice…

A: Given data- Channel Index = 5/3Orifice type outletTo Find-The value of setting

Q: the leak two gages 600m apart on the line show a difference of 140kpa. Downstream from the leak two…

A:

Q: Question 12 of 23 A flow os 0.413 m3/s was measured from a rectangular channel flowing 1.20 m wide…

A: Calculate the roughness of the lining of the channel,n=?

Q: Two pipes with C1 = 120, connected in series, discharge 4.75 cfs with a loss of head of 27 ft. Each…

A:

Q: A pipe is use to Connect two reservior, length is 1000m, headloss is 4m, flowrate is 0.6m³/s.…

A: Given data  L = 1000m  hf = 4m  Q = 0.6 m3/sec  Find diameter of pipe (D)  If  1. f = 0.02  2. n =…

Q: The design of a city water supply is shown below. Pipe 1 is 300 mm diameter and 900 m long, Pipe 2…

A:

Q: For the pipe show, determine the depth of flow. Q - 50 cfs S= 0.01 E - 0.005 u- 2.34x10 slug/ft-s…

A: Solution_1

Q: (1 A venture flume is used to measure the discharge in a rectangular channel of width Wi and…

A:

Q: Avoid truncation in the middle of solution. Thank you Water flow through a 3 in diameter pipe at a…

A: Given data in question  Diameter  Velocity  To find out  Discharge

Q: 3: Answer either A- A submerged pipe outlet has the following data: F.S.L of distributary 100.00 m,…

A: As there are two different questions and nothing is mentioned which one to solve, So as per…

Q: Determine the diameter of pipe drains that drain out 24 mishara of drainage area with drainage…

A: Given information in question  Roughness coefficient  Drainage coefficient  Gradient

Q: Situation 1: For the pipe network shown, the flow of water from the reservoir A to the junction is…

A:

Q: What is the total flow rate of the given figure if the channel slope is 0.17° and n =0.012? Use…

A:

Q: What should be the drainage capacity of the collector pipe? K=5 x 10-4 cm/s

A: Given:- The value of hydraulic conductivity (K) = 5 x 10-4 cm/s The value of H = 20 ft The value of…

Q: The Reynold's number associated with a trapezoidal channel is 3,000,000. The ratio of fluid dynamic…

A:

Q: Exercise [4] Determine the diameter of pipe drains that drain out 24 mishara of drainage area with…

A: Given data  Velocity  Mannings roughness  coefficient  Gradient

Q: The tank has a square base and is filled with water to the depth of y 0.4 m. If the 20-mm-diameter…

A: Q=A*V V=2ghV=2*9.81*0.4V=2.80142msec Q=π4d2 X2.80142π40.022X2.801420.88liter/sec

Q: In a hydraulically most efficient trapezoidal channel section the ratio of the bed width to depth is

A: Hydraulically efficient channel section: For a given slope, roughness coefficient and area of flow,…

Q: 1. Calculate the discharge through a 90 mm © sharped edge orifice. Assume Cd = 0.65.

A: Given data- Sharp Edge Orifice- Diameter of orifice (D) = 90 mm =0.090 m Coefficient of discharge…

Q: Determine the diameter of corrugated field drain required to drain area of (200 *100) m if the…

A: The given data is as follows: Area=200 m×100 mQ=3 mm/daySlope of field drain=12 cm/km

Q: Water flow through a venturi meter an inlet dia. = 100 mm and throat dia. =50 mm , P at inlet = 70…

A:

Q: The tank has a square base and is filled with water to the depth of y 0.4 m. If the 20-mm-diameter…

A: This question is related to Fluid Mechanics. In this question we calculate volumetric flow of water…

Q: Determine the size of a circular concrete pipe (n = 0.013) to carry 150 ft³/s of stormwater on a…

A: The flow rate is given by ;Q = 150 cubic ft /sec n = 0.013S = 0.007d = 3.921 ftRequired size of…

Q: What is the head loss between points A and D when the flow rate is 6 m Sofor the flow rate for each…

A:

Q: Determine the diameter of pipe drains that drain out 24 mishara of drainage area with drainage…

A: given drainage cofficient = 1.5cm/day garde = 0.004 n = 0.013