By 2050 it is predicted that the peak rainfall intensity in Eastern Leyte could rise by 15% due to climate change. Assuming that the maximum rainfall intensity was recorded at 20 mm/hr, estimate the percent change (increase/decrease) in peak runoff flow rate using the rational method in 2050. Use c = 0.65 (present) and c = 0.8 (in 2050). %3D

Q: H.W1: Draw I.L for RA, RE, VB, VC, VD, MA, MD, MC. 3m B + 3m C 2m D 4m

A:

Q: 2.. A 80016 30 loft 60016 GOⓇ ¡B 60 loft C 800 15 30 loft Req'd: Member Forces FG BF BC THR

A: To find force in member FG,BF,BC

Q: Draw the figure of level and show its parts on it.

A:

Q: 3kLf 20 ft eliste Max = Max

A:

Q: 45° 20° O-0-0-0--.

A:

Q: For the section shown below verify the following equations (7) Z section th'b' (b+h 12 (26+h B D C

A: Consider the given figure So here we have to verify J=t332b+hI12=th2b312b+h2b+h

Q: 60 kips 20 EX/ Analysis all member C G 20' F 60 kips 20 15' 30 kips 15'

A: All data is given in the figure belowneed to findforces in all member

Q: 400 N 800 N B D E IC F2 m

A: Given  Concentrated loads of 400 N and 800 N are acting at B and D respectively.

Q: Qパnele

A:

Q: draw the isometric view

A: In civil and mechanical engineering, drawing is one of the basic tools that is used to execute an…

Q: The cross section at station 2+60 has a cut area of 9 ft2 and a fill area of 4 ft2 and the cross…

A: Cut Area of the cross-section at station 2+60,A2+60=9ft²Cut Area of the cross-section at station…

Q: INSTRUCTIONS: (USE METHOD OF SECTION) A. Determine the forces in all members with () marks of the…

A: Given a truss where only few member forces are to be found Since only few member forces are to be…

Q: DRAW HE FREE BODY DIAGRAM wooDa FLANK BOX 5K6.

A: To draw the free body diagram of the given box.   The purpose of a free body diagram is to represent…

Q: determine the reading at "D"

A: A levelling staff is given, we need to find out the reading at D

Q: Replace the three couples with a single equivalent couple. F1 = 100 N; F2 = 80 N, F3 = 50 N The xyz…

A:

Q: Determine the y-coordinate of the centroid of the shaded area. y 0.25h 68° 68° --x Answer:ỹ = i

A:

Q: - What is the meaning of Cant in Turkish? A) aliyman B) clearance C) dever D) slope E)…

A: Meaning of Cant

Q: 1) Compute the coordinates of the area centroid with respect to the given axes. 2m im 2m--- Zm- Im

A: To find centroid of given figure

Q: 190, 133, 38 lcm

A: Least Common Multiple (LCM) is the smallest common multiple of two or more numbers.

Q: A steel post (E = 30x10° psi) having thickness h = in. and height l = 71 in. supports a stop sign…

A: Stress is defined as the force of resistance per unit area given by a body against deformation. The…

Q: 8k 8 k 4 ft- -4 ft- B 10 ft 2 k/ft C

A: Shear force: The algebraic sum of all the vertical forces acting at different points of the beam or…

Q: Locate the centroid (x, y) of the Composite shaded area for the coordinate axes X & Y imposed in the…

A:

Q: Determine the force and moment reactions at A for the beam which is subjected to the load…

A:

Q: Explain the following terms in 6-7 lines minimum. a) Bishop Simplified Method b) Critical Factor…

A: 1) This is the method used in stability of slopes.  2) The Bishop simplified  method uses the method…

Q: On Step 3 where do you get the sin(66.80)? reply asap.

A: Required:Explain sin(66.80) in step 3

Q: 2.. A 80016 30 love 91009 60° ¡B 60 6 loft ic 800 15 30 loft D

A: Objective: To determine the force in members FG, BF and BC.   As the objective of the question is to…

Q: Which shortcut key lets you draw a line? O RO O z TB

A:

Q: ] Use graph paper to draw simplified sketch of the gear and the rack shown in problem 5/64(79). What…

A: Figure is as shown

Q: 40" -45"-

A:

Q: B 3 ft 6 ft A 3 ft Draw SFD and BMD

A: Find the reactions consider ∑Fy=0VB+VA=12(3)(600)+600(6)+12(3)(600)as it is symmetrical beam…

Q: Find shape factor Q about the y-axis.

A:

Q: Determine the y-coordinate of the centroid of the shaded area in terms of h. !n/2 x

A:

Q: Describe about the tangent modulus.

A: Tangent modulus:- The instantaneous rate of change of stress as a function of strain. The slope of…

Q: Determine the coordinates of the centroid of the shaded are 3″ 2"

A: To find centroid

Q: 5. Draw profile for AA'. 1500m A' A 2000m B' Øm 5000m

A: A contour is given, we need to draw the profile A-A Topographic Profile:- A topographic profile,…

Q: зх 2 3x7x-2 8 X - X dx

A: I would like to know if it is x^8 or x^3. It's because I just want to be clear and this will be a…

Q: Define One-Way Eccentric or Moment Loading

A: Here ia A Basic Difference between Eccentric and Concentric/Direct Loading , Illustrated…

Q: Draw according to scale. 12km, South 11mm,12\deg South of East 22(m)/(s),45\deg North of West 75cm,…

A:

Q: Joint

A:

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).