براير المائد A. How can we increase the bandwidth of frequency response? مار انسان فرما لرووك الدليل B. Why the bandwidth of the operational amplifier is equal to the high cutoff frequency (fc)? C. Explain the common mode rejection ratio (CMRR) of operational amplifier?

براير المائد A. How can we increase the bandwidth of frequency response? مار انسان فرما لرووك الدليل B. Why the bandwidth of the operational amplifier is equal to the high cutoff frequency (fc)? C. Explain the common mode rejection ratio (CMRR) of operational amplifier?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

This problem is AC analysis problem. DC analysis is not needed to answer the question. A) If we assume that the peak voltage of Vbe must be less than 10 mV to avoid small signal violations determine the value of Rsig if Vi has a peak amplitude of 1 V and Is = 1mA. Hint: Don't forget r!! Answer: Rsig =. B) If you did the DC analysis on this problem and calculated Vc = 50 mV and Vs = -100 mV what is the maximum amplitude of the output voltage while the circuit stays in active mode. Answer: Vo,max =, When you "verify" a mode of operation you will need to calculate all three voltages (Vc, Ve, VE for BJTS and VG, Vs, Vp for MOSFETS) and show the correct two conditions are satisfied. Assume Capacitors acts like open circuits at DC and short circuits for AC. > Assume the following: 5V o Beta = 100 O VBE = 0.7 o V: (Thermal) = 26 mV o Vr (Threshold) = 2V O VA = - o For MOSFET saturation mode: assume: lp = K(VGs-Vr)? (Assume K = 10 mA/V²). 5kn C2 01 C1 Rsig 1kn 10k Vi IIs :C3 1mA -5V
3. An electrical fan is used to cool electrical components when the temperature exceeds a certain limit. The fan is controlled by a microcontroller that sends a logical-1 (3.3V) to an interface circuit that in turn activates the motor. When the temperature falls below the upper limit, the microcontroller sends a logical-0 (0.0V) to the interface circuit and the motor turns off. You are to design a simple transistor switch controller circuit for this application and decide to use the design shown Fan motor draws V2 24W when running "GND -24V D2 IN40010P u2 "DO" as NPN Transistor Ib below. You have the following npn transistors available to you: 2N2222A, SS8050, and 2N3904. a. If the fan draws 24W when running, what is the collector current, Ic? b. What would the maximum Vce voltage be across the transistor when the it is in cut-off? c. Based on the design criteria and the manufacturer's specifications for the 3 transistors, which one would work for this application? Why? d. For the…
Answer the questions about the Binary Weighted DAC: i. Design a 6-bit Binary Weighted Resistor DAC with Vref = 3.3 V, the feedback resistor RF = 16KN. Use commercially available resistors in your eircuit diagram. ii. Determine the analog output of the designed 6-bit Binary Weighted Resistor DAC, Vout for input bits (a) 100010 and (b) 101000.
Electrical Engineering Determine the following (i) Frequency of Oscillation (ii) Feedback fraction For the oscillator to start, what is the minimum (ii) value of voltage gain? If the value of L is doubled, what is the frequency of (iv) oscillation? Sketch and label the output waveform across the load resistance RL. (v) Vcc +12 V RF CHOKE C. 0.1 uF 10 ka 0.1 F C. 0.01 F R 10 ka R2 5 ka RS C 1 KAS0.1 F 0.01 uF 21 uH
a) Derive the input and output impedances of series-shunt feedback amplifier. b) Find the values of frequency of oscillation and load resistånce of FET RC phase shift oscillator with R = 10 k2, C=1 nF, and gm =3 mS.
Which statement is true? a. In FSK, the modulating signal and the carrier signal are both analog b. In FSK, the modulating signal and the modulated signala re both digital c. In FSK, the modulating signal and the modulated signal are both analog d. In FSK, the carrier signal is analog and the modulating signal is digital
3) The region where an amplifier is operating in a linear format is represented by: a) The positive feedback b) The common feedback c) The negative feedback 4) For oscillator operation the noise traveling around a loop, then being amplified as converging on a sine wave at: a) Two different frequencies b) Several frequencies c) Single frequency
Noise Figure (F) of an amplifier at room temperature is 0.2 dB. What will be the effective noise temperature (Te). Assume room temperature to be 295K.
Find the voltage attenuation ratio for a 30 dB attenuator. Show detailed calculation pls.
The equipment order in which a vibration sensor/transducer turns vibrations into a vibration spectrum is: Select one: A. Filter - Sensor – Amplifier- DisplayIncorrect B. Sensor - Filter – Averager - Display C. Sensor- Averager- Filter -Display D.None of the above Please explain your answer
Consider unity feedback system with forward path transfer function 25/s(s+ 5); what are the values of peak time and settling time? 1.6 sec, 0.726 sec 0.726 sec, 1.6 sec 0.5 sec, 0.726 sec 0.726 sec, 1 sec
lin Ас current_ VDD ✓ Tout SSEC $=67² Tin ( Bias Ckt omitted here) Unity Gain Frequency f₁ = Tout = 1 (unity) Current gain = AI Cgd_ifbk = 0 Cgs as r V₂ o di тель Tout 1. Derive an expression for ft of the fet shown above. (Please ignore the feedback current flowing through cgd) 2. Plot Ai vs frequency in the log-log scale and identify its slope (rate of decrease or increase vs. frequency) 3. Find an expression for ft in S.I. in terms of Cox.