Boxes of Honey-Nut Oatmeal are produced to contain 14.0 ounces, with a standard deviation of 0.15 ounce. For a sample size of36, the 3-sigma x chart control limits are:Upper Control Limit (UCL;) = ounces (round your response to two decimal places).Lower Control Limit (LCL;) = ounces (round your response to two decimal places).

Given, Sample size- 36 sigma- 3

Answered: Boxes of Honey-Nut Oatmeal are produced…

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

In a research on weight of cereal dispersed into a box of cereal, a company collected m=12 sets of inside ring diameter samples with a subgroup size of n=6 , the grand mean =17.8 ounces and the average range =1.02 ounces. Determine the upper control limit for an R chart. Enter your answer to 2 decimal places.
54 Boxes of Honey-Nut Oatmeal are produced to contain 14.0 ounces, with a standard deviation of 0.20 ounce. For a sample size of 64, the 3-sigma X chart control limits are: Upper Control Limit (UCL) = ounces (round your response to two decimal places).
Please do not give solution in image formate thanku.
Which of the following holds the best for a point that is outside the upper control limit of a R- chart Select one: a. should be investigated because an assignable cause of variation might be present b. is an indication that no cause of variation is present c should be ignored unless another point is outside that limit d. should be ignored because it signifies better than average quality
< Refer to Table S6.1 - Factors for Computing Control Chart Limits (3 sigma) for this problem. Sampling 4 pieces of precision-cut wire (to be used in computer assembly) every hour for the past 24 hours has produced the following results: Hour X 1 2 3 4 5 6 R 3.25" 0.65" 3.00 1.23 3.32 1.43 3.39 1.26 3.07 1.17 2.96 0.37 Hour X R Hour R Hour 7 2.95" 0.48" 13 X 3.11" 0.90" 2.73 1.36 19 20 8 2.55 1.18 14 9 0.71 3.12 1.11 21 3.12 2.85 15 16 10 1.38 2.74 0.50 22 11 2.83 1.22 17 2.86 1.38 23 12 3.07 0.45 18 2.64 1.29 24 X 4.51" 2.89 2.65 3.18 3.04 2.54 R 1.56" 1.14 1.13 0.51 1.58 1.02 Based on the sampling done, the control limits for 3-sigma x chart are (round all intermediate calculations to three decimal places before proceeding with further calculations): Upper Control Limit (UCL) = inches (round your response to three decimal places).
A control chart for fraction nonconforming is to be established using a center line of p=0.03. What sample size is required if we wish to detect a shift in the process fraction nonconforming to 0.08 with probability 0.50? 1269 475 73 316 216 2 105 150 265
Please do not give solution in image formate thanku.
A metal fabricator produces connecting rods with an outer diameter that has a 1± 0.02 inch specification. A machine operator takes several sample measurements over time and determines the sample mean outer diameter to be 1.005 inches with a standard deviation of 0.003 inch. Calculate the process capability index for this example. Note: Round your answer to 3 decimal places. Process capability index
Linda Boardman, Inc., an equipment manufacturer in Boston, has submitted a sample cutoff valve to improve your manufacturing process. Your process engineering department has conducted experiments and found that the valve has a mean (u) of 12.00 and a standard deviation (a) of 0.04. Your desired performance is μ = 12.00 +3 standard deviations, where a = 0.045. For the given information, the process capability index (Cpk) - (round your response to three decimal places).
A manufacturer is selling pharmaceuticals that have a weight specification 199.8 to 200.2 mg, with a target value of 200 mg. Before sending its next shipment, the company collects a large sample of product and determines the mean weight of the sample is 199.89 mg, with a standard deviation of 0.035 mg. The process capability index for the current process is ____. Round to three decimal places.
Lower Range, Sample Size, n Mean Factor, Upper Range, DA A2 D3 2 1.880 3.268 3 1.023 2.574 4 0.729 2.282 5 0.577 2.115 6 0.483 2.004 7 0.419 1.924 0.076 8 0.373 1.864 0.136 0.337 1.816 0.184 10 0.308 1.777 0.223 12 0.266 1.716 0.284
A component part for a motorcycle is manufactured by an investment casting process. The air vent opening on this casting is an important functional parameter of the part. The results for five samples are given in the table. The values given have been coded using the last two digits of the dimension Sample Air vent opening diameter (in mm 1 58 61 54 60 2 61 55 58 62 3 66 60 59 55 4 53 57 58 64 5 65 63 79 61 Determine the central line and control limits for the range and mean charts, and discuss whether or not the process is in statistical control.

SEE MORE QUESTIONS

Recommended textbooks for you

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Business in Action

Operations Management

ISBN:

9780135198100

Author:

BOVEE

Publisher:

PEARSON CO

Purchasing and Supply Chain Management

Operations Management

ISBN:

9781285869681

Author:

Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. Patterson

Publisher:

Cengage Learning

Production and Operations Analysis, Seventh Editi…

Operations Management

ISBN:

9781478623069

Author:

Steven Nahmias, Tava Lennon Olsen

Publisher:

Waveland Press, Inc.

SEE MORE TEXTBOOKS