Bitwise AND operation is needed to obtain the subnet number. Given an IP Address and Subnet Mask, by performing bit wise AND operation, the corresponding Subnet Number can be obtained (think about the "neighborhood" name, or your family's last name – that's the subnet number). In routers, the routing tables essentially use the subnet numbers to build the routing tables and route the packets to different networks (i.e., to different "neighborhoods") Calculate the bit-wise and operation of IP address and subnet mask to get the subnet. Examples: 1. What is subnet number of IP Address 60.60.60.2 with a subnet mask of 255.255.255.240? 60.60.60.2 in binary = 00111100.00111100.00111100.00000010 255.255.255.240 in binary = 11111111.11111111.11111111.11110000 AND Result in binary: Therefore, the subnet number is in decimal notation: Please do the same calculation as above by completing the table below (make sure to show your work): /n prefix /24 IP Address Subnet Mask Subnet Number 144.130.42.117 255.255.255.0 8.162.16.17 255.255.224.0 50.30.152.59 255.248.0.0 196.172.17.100 255.255.255.192

Bitwise AND operation is needed to obtain the subnet number. Given an IP Address and Subnet Mask, by performing bit wise AND operation, the corresponding Subnet Number can be obtained (think about the "neighborhood" name, or your family's last name – that's the subnet number). In routers, the routing tables essentially use the subnet numbers to build the routing tables and route the packets to different networks (i.e., to different "neighborhoods") Calculate the bit-wise and operation of IP address and subnet mask to get the subnet. Examples: 1. What is subnet number of IP Address 60.60.60.2 with a subnet mask of 255.255.255.240? 60.60.60.2 in binary = 00111100.00111100.00111100.00000010 255.255.255.240 in binary = 11111111.11111111.11111111.11110000 AND Result in binary: Therefore, the subnet number is in decimal notation: Please do the same calculation as above by completing the table below (make sure to show your work): /n prefix /24 IP Address Subnet Mask Subnet Number 144.130.42.117 255.255.255.0 8.162.16.17 255.255.224.0 50.30.152.59 255.248.0.0 196.172.17.100 255.255.255.192

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Related questions

Q: With Network Address Translation, a router changes a private IP address in the IP header to the…

A: Translation of Network Addresses (NAT): When visiting the Website, we'll need one gateway, and then…

Q: We have 5 routers labled A-E. Suppose we have the forwarding tables shown below after the routing…

A: To send a message from A to E , the least possible cost is 2 and there are two paths having cost 2…

Q: A link between two hosts may carry many packets at once. Please give a timetable outlining all the…

A: It has to be made clear that many packets may be transmitted at once.

Q: The Routing Information Protocol (RIP) is an intradomain routing based on routing. * link state…

A: According to the guidelines we are supposed to answer only 1 question. So I am going with the first.…

Q: A router needs to transmit an IPv4 datagram with a total size of S bytes. The link layer of the…

A: ATM Adaption Layer 5 (AAL5) is used to send variables of length packets up to 65,535 octets in size…

Q: Give forwarding tables for each of the switches A-E in the following network. Destinations are A-E…

A: BELOW ? STEP BY STEP COMPLETE SOLUTION REGARDING YOUR PROBLEM WITH EXPLANATIONS :

Q: With Network Address Translation, a router changes a private IP address in the IP header to the…

A: Option : Destination Port Checksum Length

Q: Consider a network with 4 links between two hosts where the maximum allowable packet size is 1000…

A: Answers:- 1st method:- To calculate the total time it takes to send 6000 bits from one host to…

Q: There are 4 routers Router A, B, C and D Router B and D are connected in a network system, RIP is…

A: Routing Information Protocol (RIP) is a distance-vector routing protocol. Routers running the…

Q: Each active interface of Distance vector gets frequent transmissions of the whole routing table that…

A: Introduction: Data transport in packet switched networks uses distance vector and link state routing…

Q: To begin, let's take a closer look at routing. Identify the difference between two popular routing…

A: The capacity to forward IP packets from one network to another is referred to as routing. An IP…

Q: True or false: When a BGP router receives a path from its neighbor that is marketed, it has to apply…

A: Border Gateway Protocol (BGP): The Border Gateway Protocol (BGP) is an inter-autonomous computer…

Q: To begin, let's take a closer look at routing. Identify the difference between two popular routing…

A: Introduction: Routing is the capacity to transfer IP packets—data packages having an Internet…

Q: When it comes to routing, what precisely is it, and how does it work? In this post, we will look at…

A: Network routing is the process of selecting a route through one or more networks. Routing principles…

Q: The word "overlay networks" means precisely what it sounds like. Are routers included in this…

A: Introduction: a network with edges and routers known as an overlay network As a result, the overlay…

Q: CIS269 Packet Translation Lab Break down the following IP datagram into its individual…

A: Break down the following IP datagram into its individual fields, listing the value of each. Hint:…

Q: In IEEE 802.11, two-way communication is used to authenticate an open system. In order to…

A: Answer : 1.) Open System Authentication is the process by which a computer can gain access to a…

Concept explainers

Types Of Protocols

A network protocol is a collection of rules that governs the exchange of data between devices connected to the same network. In other words, network protocols are rules that specify how devices communicate or transfer data over a network. The sender and receiver systems must obey the standards to facilitate communication between them.

Question

Bitwise AND operation is needed to obtain the subnet number. Given an IP Address and Subnet Mask,
by performing bit wise AND operation, the corresponding Subnet Number can be obtained (think about
the "neighborhood" name, or your family's last name – that's the subnet number). In routers, the
routing tables essentially use the subnet numbers to build the routing tables and route the packets to
different networks (i.e., to different "neighborhoods")
Calculate the bit-wise and operation of IP address and subnet mask to get the subnet.
Examples:
1. What is subnet number of IP Address 60.60.60.2 with a subnet mask of 255.255.255.240?
60.60.60.2 in binary =
00111100.00111100.00111100.00000010
255.255.255.240 in binary =
11111111.11111111.11111111.11110000
AND Result in binary:
Therefore, the subnet number is in decimal notation:
Please do the same calculation as above by completing the table below (make sure to show your work):
/n prefix
/24
IP Address
Subnet Mask
Subnet Number
144.130.42.117
255.255.255.0
8.162.16.17
255.255.224.0
50.30.152.59
255.248.0.0
196.172.17.100
255.255.255.192

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.

Similar questions

To begin, let's take a closer look at routing. Identify the differences between two popular routing methods.
A=32, B=33, C=34, D=35 x1, y1, z1 are the interfaces for the router gateway, while x2, x3, y2, y3, z2, z3 are for the router interface Find the Routing Table R1, R2, and R3 using the following table! Destination Next Hop Interface With the Routing Table that you have specified in point a, which path will PC1B take when communicating with PC2B and PC3B In theory there is a routing table for Network Address 0.0.0.0 with a Subnet Mask of 0.0.0.0, explain the function of this routing table? Does the image network require routing at point c? Why?
Comparison should be made between the routing protocols DSDV, AODV, and DSR with regard to the protocol type, routing methodology, routing structure, route selection, routing table, and route management. The workings of the protocol, its advantages, and its drawbacks.
A simple CIDR routing table is shown in Figure 1. For each of the destination IP addresses below, indicate which entry in the table it matches. Indicating none if no routing entry can be matched (hint: given an IP packet, the router will check whether there is a routing entry which can be used to route this packet, by checking the destination IP address in the packet with each routing entry: based on the subnet mask of each routing entry, it can extract the network ID and compare it with each routing entry; if there are a few routing entries which can match, the entry with the longest subnet mask wins). Address Mask Output Port 10.19.0.0/16 1 10.19.128/17 2 10.19.192/18 3 10.19.192/19 4 0.0.0.0/1 5 141.219.2.10 10.10.10.10 10.19.86.141 10.19.193.6 10.19.255.86 10.19.192.18
A connection that connects two hosts may transport many packets at the same time. Please provide a schedule that outlines all of the actions that need to be completed in order to successfully execute one shipment. Is it to be anticipated that one of the delays will take a certain amount of time, while the duration of the other delay may be adjusted in accordance with the circumstances?
Each active interface of Distance vector gets frequent transmissions of the whole routing table that Distance vector maintains. The link status protocol broadcasts information about the state of a router's own connections to all other routers in the network. Each statement has two ideal examples that show how the Link state and the Distance vector may be utilized in a number of circumstances.
An Internet user would like to transfer a message from his computer (host A) to another computer (host B). The size of the message passed to the IP layer is 3800 bytes. The datagram(s) carrying the message will have to cross two routers (R1 and R2) and 3 networks (NET1, NET2, and NET3) as described in the above figure. Each of these networks has a specific MTU (for example the MTU of network 1 is 1500 bytes. MTU here stands for Maximum Transmission Unit, the largest data that a frame can carry). Fill the table with the IP datagram(s) needed right after passing through NET3 (no need to show your fragmentation for N1 or N2). Assume a 2-byte options in the header. Show all your details (for partial points in case your numbers are incorrect). NET1 MTU=1500 R1 NET2 MTU=640 R2 NET3 MTU 1500 V BIU Fragment # Format Offset Flag (3 bits) Data Length Total Length ...
A connection that connects two hosts may transport many packets at the same time. Please provide a schedule that outlines all of the actions that need to be completed in order to successfully execute one shipment. Is it anticipated that one delay would take a certain amount of time, whilst the duration of the other delay will be subject to change depending on the circumstances?
It is possible for a series of packets to be sent from one host to another utilizing the same route between the hosts. Please break down the time it takes for a single package to go from beginning to conclusion. Is it expected that one of the delays would last for a certain period of time, while the other delay's length remains open?