Binary data has to be transmitted over a telephone link that has a usable bandwidth of 3000Hz and a maximum achievable signal-to-noise power ratio of 6 dB at its output.. a. Determine the maximum signaling rate and probability of error if a coherent ASK scheme is used for transmitting binary data through this channel. b. If the data is maintained at 300 bits/sec, calculate the error probability.

Binary data has to be transmitted over a telephone link that has a usable bandwidth of 3000Hz and a maximum achievable signal-to-noise power ratio of 6 dB at its output.. a. Determine the maximum signaling rate and probability of error if a coherent ASK scheme is used for transmitting binary data through this channel. b. If the data is maintained at 300 bits/sec, calculate the error probability.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a. Develop a time delay procedure for the 3.0 GHz Pentium-Core2 that waits for 50ms b. The 8255 shown in the following is configured as follows: port A as output, B as input, and port C (low and high) as output. 1. Find the port addresses assigned to A, B, C and the control register 2. Find the control byte (word) for this configuration. 3. Program the ports to input data from port B and send it to both ports A and C. Hint you can use delay in (a) if needed AO A3 A4 A5 A6 A7 10/M DO D7 IOW- IOR- A2 A1 DO D7 WR RD A0 Al OCS A B CL CH
b) An 10 bits single channel PCM system gives an output of 102 kilo bit per second(kbps). Calculate: i. The sampling frequency of the system. ii. The highest possible modulating frequency of the system. iii. The bit duration of the system. iv. The Bandwidth of the system.
Plz solve it
B) Twenty four speech signals the channel and minimum required bandwidth. are TDM-PAM transmitted, find minimum sample rate at
Ex (3):- A signal that has the highest frequency component of 4.2MHZ and a peak to peak value of 4 volts is transmitted using a binary PCM. The number of quantization levels is 512 and P=0.04W calculate: 1. Code word length. 2. Bite rate.
9-A binary data source has P(OT) = 3/8, due to interference of channel, then P(OR/1T) = 1/16 and P(1R/0T) = 3/4. Calculate the noise and losses entropies and compare with source entropy.
Consider a telephone line initially noiseless channel having bandwidth and signal level determined by the network engineer. Calculate maximum data rate. After certain distance the channel becomes extremely noisy, so that the noise is strong which faints the signal .Calculate the capacity of the channel.
For a PCM system, the value of the minimum transmission bandwidth is 25 kHz and the maximum frequency of the input waveform is 5 kHz. Estimate the total number of levels in the uniform quantizer present.
Don't need to elaborate the answer. Just write down the correct answer. Some questions may have multiple answers. 1) Which multiplexing technique shifts each signal to a different carrier frequency? a) FDM b) TDM c) WDM d) PDM 2) Which multiplexing technique involves signals composed of light beams? a) FDM b) TDM c) WDM d) PDM 3) We need an addressing mechanism in a) Satic b) Parallel c) Synchronous d) Statistical 4) Pulse stuffing is a strategy used in a) TDM b) FDM c) FHSS d) WDM 5) a) FDM b) TDM technique uses multiple carrier frequencies. c) WDM d) FHSS e) DSSS TDM. 6) We need to use synchronous TDM and combine 20 digital sources, each of 100 Kbps. Each output slot carries 1 bit from each digital source, but one extra bit is added to each frame for synchronization. Answer the following questions: i) What is the size of an output frame in bits? a) 10 b) 20 c) 21 d) 11 ii) What is the output frame rate? a) 200000 frames/sec b) 210000 frames/sec c) 10000 frames/sec d) 100000…
The transmitted bit stream consists of 25 bits of repeating (arrow to theleft) 11000 and the transmission bit rate is 600 bits/second using ASKwith the 5V, 1800 Hz carrier. (a) Determine the fundamental frequencyrange of the transmitted ASK signal. (b) If the ASK signal is transmitted ona noiseless channel with a bandwidth of 1200Hz. Determine the peakamplitude of the received ASK signal. Answer this item in this format:
Incoming binary information is encoded by a typical modem into QPSK and 16- PSK scheme. Modem operates at data rate of 2400 bps. Amplitude of the encoded signal is 10mV peak. Noise power at receiver is 100 nW. Calculate Eb/N0 in dBm.