Binary Counters Objective: Design. construct, and test a three-bit counter that counts up or down. A disable input D determines whether the counter is on or off. If D=1, the counter is disabled and remains at its present count even thoughclock pulses are applied to the flip-flops. • If D=0, the counter is enabled and a second input, x, determines the directionof the count. • If x=1, the circuit counts the sequence 00, 01, 10,11 and the count repeats. • If x=0, the circuit counts the sequence 11, 10, 01, 00 and the count repeats. (Do not use D to disable the Clock) Note: Design the sequential circuit with D and x as inputs. Submission: Reports must include all schematics and cost of design. Compare your results with other solutions. (Costs, design....). Define why your design is better.

Binary Counters Objective: Design. construct, and test a three-bit counter that counts up or down. A disable input D determines whether the counter is on or off. If D=1, the counter is disabled and remains at its present count even thoughclock pulses are applied to the flip-flops. • If D=0, the counter is enabled and a second input, x, determines the directionof the count. • If x=1, the circuit counts the sequence 00, 01, 10,11 and the count repeats. • If x=0, the circuit counts the sequence 11, 10, 01, 00 and the count repeats. (Do not use D to disable the Clock) Note: Design the sequential circuit with D and x as inputs. Submission: Reports must include all schematics and cost of design. Compare your results with other solutions. (Costs, design....). Define why your design is better.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Design a 3-bit counter which counts in the sequence: 001, 010, 110, 011, 111, 101, 100, (repeat) 001, ...
Design a two-bit binary counter with a single input x. When the input x=0, the counter stopscounting and when the input x=1, the counter continues counting. In your design use JK flipflops. Show the state diagram and the state table. https://www.bartleby.com/questions-and-answers/design-a-two-bit-binary-counter-with-a-single-input-x.-when-the-input-x0-the-counter-stops-counting-/626ccbfb-139d-4915-ac6c-cefd6abe5667
Assuming the above counter starts in (0) state, what will be the count after 144 input pulses?
digital design
Construct the circuit of the following function using 3:8 decoder and 2:4 decoder only: F(A,B.C.D) =(A+D)(C+D) NB1: You must use both the decoders. Your circuit should be cost efficient, meaning you have to use the lowest number of components possible. NB2: You can use external gates for connecting inputs/outputs if required.
Design a reverse counter with three D flip‐flops A, B and C. The counter counts from 7, 6, …, 0, then to 7, and continues.
Design a modulo-6 counter, which counts in the sequence 0, 1, 2, 3, 4, 5, 0, 1, .... The counter counts the clock pulses if its enable input, w, is equal to 1. Use D flip-flops in your circuit. Repeat Problem 6.23 using JK flip-flops. Repeat Problem 6.23 using T flip-flops.
Please solve
Draw the equivalent one flip-flop per state of the given ASM chart.
Q 1:- for the state diagram shown below, connect the circuit using J-K Flip-Flop. 0/0 1/0 1/0 00 01 0/0 0/1 11 10 0/1 1/0 1/0
Assume that we have a counter that resets to 0000 on the tenth pulse and starts over again. In other words, the output will never represent a number greater than 10012 = 910. Design the logic circuit that produces a HIGH out put whenever the count is 2,3, Or 9. Use K-map and take advantage of the don't-care conditions.
The next state table of a 2-bit saturating up- counter is given below. Q1 Qo Qi Q0 1 1 1 1 1 1 1 1 The counter is built as a synchronous sequential circuit using T flip-flops. The expressions for T1 and To are