Bearing stress 5. Please provide proper discussion and illustration also complete solution and clear solution please thank you A solid shaft is designed to transmit 50kN @ 1800 rpm to a gear by means of 156 mm long key with square cross-section. The shaft diameter is 35.6mm. What should the cross-section be in mm2 to resist shearing, if the allowable shear stress on the key is 20 MPa?

Q: A steel shaft of 2.5 inch diameter rotates at 500 rev/min and transmits 120 hp through a gear.…

A:

Q: e diameter

A: To find Outside diameter(d2)

Q: Find the minimum shaft diameter (dmin) of the gear system given the dimensions and load values.  A…

A:

Q: The nature of the stresses

A: Given; A helical gear with pressure angle,α= 200 and β=300 helix angleAt the  mid span of a shaft is…

Q: Compute the torsional shear stress in a circular shaft with a diameter of 50 mm that is subjected to…

A: GivenT=800 Nmd=50mm=0.05 mFormulaσT=16Tπd3

Q: A straight bevel gear pair has the following data: Np = 25; NG = 50: P = 10; 20° pressure angle. If…

A: given; number of teeth of gear (TG)=50number of teeth of pinion (Tp)=25speed of…

Q: Determine the minimal value of a radius of the circular-solid shaft in problem 1 such that the…

A:

Q: An input shaft of a gearbox with motor power P = 7 kW and rotation number n = 1300 rpm. The diameter…

A:

Q: PROBLEM 2 A drive shaft running at 2500 rpm has outer diameter of 80mm and inner diameter of 60mm.…

A:

Q: A planetary gear used on the Mars rover uses a 25-tooth helical gear with ψ = 20° has a 25° pressure…

A: Given Data The number of tooth are: N=25 The angle of the thread is: ψ=20° The pressure angle is:…

Q: a uniformly loaded conveyor with a required shaft speed of approximately 531 r/min. Use a pinion…

A:

Q: Problem : A train of spur gears with 20°full-depth involute teeth is shown in the Figure below. Gear…

A: Here Given                    Power P=5000 WattN1=720 rpmT1=20T2=50T3=30T4=60m=4mmϕ=20°Radius of…

Q: Figure below shows a portion of a pump that is gear-driven at uniform load and speed. The 25 mm…

A:

Q: cast St gear angle has to 33 kW at 2000 r.p.m. If the gear has 25 teeth, find the necessary module,…

A: In helical gear the teeth of the gear remains in the form of helix around the gear. There is a…

Q: 5.2 A hollow bronze shaft of 75 mm outside solid steel shaft of 50 mm diameter and of the same…

A: Note: As per our guidelines we are supposed to answer only the first 3 sub-parts. Kindly repost…

Q: In the double-reduction gear train shown (dimensions are in inches), shaft a is driven by a motor…

A: Step 1: Step 2: Step 3:

Q: A solid 1.5 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant.…

A:

Q: angle angle and 3 1 ween two bearin

A:

Q: A motor provides 60 hp power to a wheel B. It rotates a solid shaft in AISI 1020 steel, 4 cm in…

A:

Q: A chain drive using bush roller chain transmits 5500 W of power. The driving shaft on an electric…

A: Given Data Transmitted power is: P=5500 W The speed of the drving shaft is: n=1440 rpm The velocity…

Q: A hollowed circular shaft that can transfer a 20 kN-m torque has the characteristics 72mm for the…

A:

Q: Oh no! The bearing at the wall on the left has been damaged. It is now acting like another gear that…

A:

Q: Q5 The figure shows a shaft carrying three gears that rotates at 1150 rpm. Gear A =10kw delivers…

A: Given,  NA=NB=NC= 1150rpmFor Gear A, PA= 10kw                              = 10×103wFor Gear C, PC=…

Q: What is the maximum diameter (mm) of a solid steel shaft that will not twist through more than 3…

A: Given: Maximum twist allowed, θ=3°Length of the shaft, L=6 mTorque applied, T=14 kN.mShear modulus,…

Q: A solid 2.0 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant.…

A:

Q: 1.Please design a pair of spur gears in the milling machine. It is known that power input is 7.5kW,…

A: Given : P = 7.5 kW N = 1450 rpm u = 2.08 To find : Design pair of spur gears Note : some values are…

Q: Problem : A train of spur gears with 20°full-depth involute teeth is shown in the Figure below. Gear…

A: given; φ=200power(P)=50Kwspeed(N)=300rpmSyt=380MPaFOS=2diameter of shaft(d)=?

Q: (b)A pair of 14.5 degree full depth spur gears are used to transmit 20kW between shafts 40 cm apart…

A: Write the relation in diameters of gears. Dg+Dp2=400 mmDg+Dp=800   ...... (1)   Again with linear…

Q: Design a hallow shaft (Diameter and length) that develops 80 kW of power while rotating at a speed…

A:

Q: A compound spur gear train with teeth as indicated in the figure with a module of 12mm and a…

A:

Q: 2-Falcon company Nizwa is conducting a campus interview to you. You are asked to design the…

A:

Q: Derive the equation of internal torques of section AB, i.e. torque for brass sleeve Tb and torque…

A: Note:- Here specific Matric number is not given so I took first matric number from give example.For…

Q: A gear drive is required to transmit a maximum power of 22.5KW, the velocity ratio is 1:2 and the…

A: First, we need to calculate the module of the gear. The module (m) is the ratio of the pitch…

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.