Answered: beam having section modulus 5000mm3 is…

beam having section modulus 5000mm3 is subjected to a bending moment of 20kNmm. Find the maximum bending stress induced in the beam. Assume E=70GPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.13.5P: A rectangular beam with notches and a hole (see figure) has dimensions h = 5.5 in., h1= 5 in., and...

See similar textbooks

Similar questions

A rectangular beam with notches and a hole (see figure) has dimensions h = 5.5 in., h1= 5 in., and width b = 1.6 in. The beam is subjected to a bending moment M = 130 kip-in., and the maximum allowable bending stress in the material (steel) is emax = 42,000 psi. What is the smallest radius Rminthat should be used in the notches? What is the diameter dmixof the largest hole that should be drilled at the mid height of the beam?
The hollow box beam shown in the figure is subjected to a bending moment M of such magnitude that the flanges yield but the webs remain linearly elastic. (a) Calculate the magnitude of the moment M if the dimensions of the cross section are A = 15 in., A] = 12.75 in., h = 9 in., and ey =7.5 in. Also, the yield stress is eY = 33 ksi. (b) What percent of the moment M is produced by the elastic core?
A rectangular beam with semicircular notches, as shown in part b of the figure, has dimensions h = 0,88 in. and h1 = 0.80 in. The maximum allowable bending stress in the metal beam is emax = 60 ksi, and the bending moment is M = 600 lb-in. Determine the minimum permissible width bminof the beam.
The cross section of a rectangular beam having a width b and height h is shown in part a of the figure. For reasons unknown to the beam designer, it is planned to add structural projections of width b/9 and height d/9 the top and bottom of the beam (see part b of the figure). For what values of d is the bending-moment capacity of the beam increased? For what values is it decreased?
A simple beam A B of a span length L = 24 ft is subjected to two wheel loads acting at a distance d = 5 ft apart (see figure). Each wheel transmits a load P = 3.0 kips, and the carriage may occupy any position on the beam. Determine the maximum bending stress Gmaxdue to the wheel loads if the beam is an I-beam having section modulus S = 16.2 in3. If d = 5 ft. Find the required span length L to reduce the maximum stress in part (a) to 18 ksi. If L = 24 ft, Find the required wheel spacing s to reduce the maximum stress in part (a) to 18 ksi.
A frame ABCD is constructed of steel wide-flange members (W8 x 21; E = 30 x ID6 psi) and subjected to triangularly distributed loads of maximum intensity q0acting along the vertical members (see figure). The distance between supports is L = 20 ft and the height of the frame is h = 4 ft. The members are rigidly connected at B and C. Calculate the intensity of load q0 required to produce a maximum bending moment of 80 kip-in. in the horizontal member BC. If the load q0 is reduced to one-half of the value calculated in part (a), what is the maximum bending moment in member BC? What is the ratio of this moment to the moment of 80 kip-in. in part (a)?
.20 Determine the plastic moment Mpfor beam having the cross section shown in the figure ey=210 MPa.
A simple beam ACE is constructed with square cross sections and a double taper (see figure). The depth of the beam at the supports is dAand at the midpoint is dc= 2d 4. Each half of the beam has length L. Thus, the depth and moment of inertia / at distance x from the left-hand end are, respectively, in which IAis the moment of inertia at end A of the beam. (These equations are valid for .x between 0 and L, that is, for the left-hand half of the beam.) Obtain equations for the slope and deflection of the left-hand half of the beam due to the uniform load. From the equations in part (a), obtain formulas for the angle of rotation 94at support A and the deflection Scat the midpoint.
Two identical, simply supported beams AB and CD are placed so that they cross each other at their midpoints (sec figure). Before the uniform load is applied, the beams just touch each other at the crossing point. Determine the maximum bending moments (mab)max* and (MCD)max beams AB and CD, respectively, due to the uniform load if the intensity of the load is q = 6.4 kN/m and the length of each beam is L = 4 m.
A beam ABC is fixed at end A and supported by beam DE at point B (sec figure). Both beams have the same cross section and are made of the same material. Determine all reactions due to the load P. What is the numerically largest bending moment in cither beam?
A rectangular bar having width twice the depth is used as a beam. The beam is made of mild steel material having elastic modulus of 2.1 x 105 N/mm? and it undergoes bending by external load which makes radius of curvature of 150 m. If the allowable bending stress in the beam is to be limited to 100 MN/m. find the cross section of the beam.
An A-36 steel beam of following cross section is part of a bridge and it is subjected loading as shown. mmmmm 35 ft 250 lb/ft 10 in 35 ft 50 ft 25 in 600 lb/ft * Assume that the bridge has a self-weight of 250 lb/ft and due to the truck, the loading is now 600 lb/ft for the 50 feet section as shown in the picture above. Now if the maximum bending moment due to the truck is 865.625 kip-ft, that translates to a maximum bending stress as shown in the table below. 25 in 50 ft 35 ft Maximum Bending stress (kpsi) Cross-sectional shape Yield strength of steel Moment of inertia of beam A-36 9.97 kpsi Rectangular I-shaped Beam 36 kpsi 36 kpsi 21.633 kpsi The cross-sectional dimensions of both shapes are shown below. 250 lb/ft 10 in 35 ft (in) 13020 6290 Consider yourself as an engineer assigned to this bridge construction and discuss the suitable options for the optimal cross-section of the bridge. Note that from the data shown in the table, both rectangular and I-beam cross-sections have…