Basic force sensor. The ceiling of a large building is supported by 16 verticalsteel tubes, each with an inner diameter of 100 mm and an outer diameter of140 mm. Each tube is equipped with a 240 2 strain gauge (nominal, unstressedresistance at 20°C), prestressed to 2.5% strain. The Young's modulus for steel is200 GPa. The strain gauge has a gauge factor of 2.2.6.6a. If the maximum strain mneasured is 2% in each tube, what is the maximumweight of the roof?b. What is the change in the resistance of the strain gauge and what is the actualresistance reading for maximum allowable weight?C. If the expected temperature range is 0°C-50°C, what is the error in reading ofthe maximum weight, assuming the sensor is not temperature compensatedand it is made of constantan?

Answered: Image /qna-images/answer/cd27b92e-08b7-486c-aeb0-22bd62f1fd03.jpg

Basic force sensor. The ceiling of a large building is supported by 16 vertical steel tubes, each with an inner diameter of 100 mm and an outer diameter of 140 mm. Each tube is equipped with a 240 2 strain gauge (nominal, unstressed resistance at 20°C), prestressed to 2.5% strain. The Young's modulus for steel is 200 GPa. The strain gauge has a gauge factor of 2.2. a. If the maximum strain measured is 2% in each tube, what is the maximum weight of the roof? b. What is the change in the resistance of the strain gauge and what is the actual resistance reading for maximum allowable weight? c. If the expected temperature range is 0°C-50°C, what is the error in reading of the maximum weight, assuming the sensor is not temperature compensated and it is made of constantan?

Basic force sensor. The ceiling of a large building is supported by 16 vertical steel tubes, each with an inner diameter of 100 mm and an outer diameter of 140 mm. Each tube is equipped with a 240 2 strain gauge (nominal, unstressed resistance at 20°C), prestressed to 2.5% strain. The Young's modulus for steel is 200 GPa. The strain gauge has a gauge factor of 2.2. a. If the maximum strain measured is 2% in each tube, what is the maximum weight of the roof? b. What is the change in the resistance of the strain gauge and what is the actual resistance reading for maximum allowable weight? c. If the expected temperature range is 0°C-50°C, what is the error in reading of the maximum weight, assuming the sensor is not temperature compensated and it is made of constantan?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The strain € is given in terms of SR, R₁ (the unstrained strain gauge resistance) and GF y SR GF R₁ Determine an expression for the uncertainty in e in terms of A(8R), AGF and AR1. Call this Ae.
Read and Solve carefully please Write clearly and Box the Final answer Express your answer to 3 Significant figures and include appropriate units. QUESTION : A long slender two-force member of cross-sectional area 2.17 mm2 is preloaded with a tensile force of 0.44 kN. A strain gauge is then applied to the member which is subject to time-varying loading with reading varying from -241 micro-strain to 50 micro-strain. Determine the minimum stress in the member in units of MPa.
Q1: A specimen made from Titanium with diameter 4 mm subjected to force of 2500 N. The specimen extended by 0.422 mm. If the young modulus is 107 GPa. Find the gauge length of specimen.
A strain gauge is bonded to a beam 200 cm long and has a cross-sectional are 8 cm² modulus for steel is 207 GN/m². The strain gauge has an unstrained resistance of 220 ohm and a gauge factor of 2.3 When a load is applied, the resistance of gauge changes by 0.011 ohm Calculate the change in length of the steel beam and the amount of force applied to the beam.
An aluminium tensile test specimen has a diameter, d = 25 mm and a gauge length of Lo = 250 mm. If a force of 175 KN elongates the gauge length by 1.25 mm, the moduls of elasticity of the material is nearly
A 45° strain gauge rosette placed on a stainless steel structure results in the following values being determined for the maximum and minimum principal strains: €1 = 1,625.9 ×10–6 and €2 = -753.4 x10-6. Assuming plane stess, determine the factor of safety against the Tresca criterion. For stainless steel, use Young's modulus E = 196 GPa, Poisson's ratio v = 0.29 and yield stress oy = 1120 M Pa. Give your answer to 2 decimal places.
To draw the shear stress-strain diagram, the collected data needed are the force applied on the specimen and its displacement. Select one: a. False O b. True
The strain of a component, which has a tensile modulus of 7 X 105 MPa, and subjected to a stress of 9000KPa, is a. 0.000026 b. 0.000129 c. 0.0026 d. 0.0000129
If the cylinder has the following strain gages readings under internal pressure of 3000 MPa, the Lateral strain reading is obtained from Strain Gauge 1 Strain Gauge 2 Strain Gauge 6 556.1 -188.8 542.7 Select one: a. 1 and 6 b. 6 С. 2 d. 1
A spherical pressure vessel has an inside diameter of 4 m and a wall thickness of 15 mm. The vessel will be constructed from structural steel [E = 200 GPa; v = 0.29] that has a yield strength of 203 MPa. If the internal pressure in the vessel is 1930 kPa, determine the factor of safety with respect to the yield strength. 1.58 2.21 O 1.30 1.45 O 1.13
A single strain gauge is mounted to measure the axial strain in a simple tensile member the recorded strain is 200 microstrain, what is the axial stress ? a) If the member is of steel? b) if the member is of aluminium ? The modulus of elasticity of steel is 200 GN/m² and that of aluminium is 70 GN/m²
During a test, a copper specimen alloy having a diameter of 10.2 mm is applied with a tensile load of 8900 N. Given a maximum allowable elongation of 0.25 mm, determine the maximum length (mm) of the specimen before deformation.