B/A 3-phase, 4-pole, 400V, 50Hz, IM, 0.85 lagging power factor has a star connected winding requires 19.68A at full load slip of 3%. Find the iron losses, output horse power and the efficiency. If the no-load power is 1200w and no-load current is 6A and Pfw is 300w, R₁ is 0.802/phase. Use EEC. 484% 1.)

B/A 3-phase, 4-pole, 400V, 50Hz, IM, 0.85 lagging power factor has a star connected winding requires 19.68A at full load slip of 3%. Find the iron losses, output horse power and the efficiency. If the no-load power is 1200w and no-load current is 6A and Pfw is 300w, R₁ is 0.802/phase. Use EEC. 484% 1.)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

None
What are the conditions in paralleling of these DC Generators:a. Shuntb. Seriesc. Compound
A 1-ph transformer 25kVA, 330/110 V, 50Hz, Req2 = 0.0452 and Xeq2 = 0.065 draw the Kapp regulation diagram referred to primary then use the diagram to calculate the regulation up at full-load and power factor of 0.8 lag and lead, 0.6 lag and lead.
1. A3-phase, star-connected alternator is rated at 15000 kVA, 11 kV. The armature resistance is I-5 S/phase and synchronous reactance is 300/phase. To what value will the terminal voltage rise when full-load at p.f. 0-8 lagging is switched off? [13970 V]
A three phase, 440V, 4-pole, 50Hz, IM, has a star connected winding requires 19.68A- at full load slip of 3% and 0.8 power factor. Find the iron loss, output power and efficiency. If the no-load power is 1200W and no-load current is 6A and Pfw is 300W, R₁ is 0.802/phase. Use EEC. 1
Please solve Last time Rejected i give upvote. Two single phase scott-connected transformers supply a 3-phase 4-wire 50Hz distribution system with 400 V between lines. The H.V. windings are connected to a 2-phase 6000V (per phase) system. The core area is 250cm². While the maximum allowable flux density is 1.2 T. Determine the point to be tapped for the neutral wire on the 3-phase side.
A 1-ph transformer 25kVA, 330/110 V, 50Hz, Req2 = 0.04522 and Xeq2 = 0.0659 draw the Kapp regulation diagram referred to primary then use the diagram to calculate the regulation up at full-load and power factor of 0.8 lag and lead, 0.6 lag and lead.
can you answer this thanks
In a Three-phase alternator, a given field current produces an armature current of 250 A on short-circuit and a generated e.m.f. of 1500 V on open-circuit. Calculate the terminal p.d. when a load of 250 A at 6.6 kV and 0.8 p.f. lagging is switched off. Calculate also the regulation of the alternator at the given load. Subject: Electrical engineering
Two transformers A and B are connected in parallel to a load of (2+j1.5) ohms. Their impedances in secondary terms are ZA= (0.15+j0.5) ohm and ZB = (0.1+j0.6) ohm. Their no-load terminal voltages are Ex=207 volt and EB-205 volt. Find the power output and power factor of each transformer.
A 500 MVA synchronous machine has H, = 5.6 MJ/MVA and a 1200 MVA machine has H₂ = 2.0 MJ/MVA. The two machines operate in parallel in a power station. What is the equivalent. H constant for the two, relative to a 100 MVA base?
19. Two single phase generators operating in parallel have no-loads emfs of E₁ = 24020° V and E₂ = 240/10° V and respective synchronous reactance of Xs1 =j2.5 ohms and Xs2 = j3.1 ohms. Resistances are neglected. The common load is purely resistance of 10 ohms. Find the common terminal voltage in volts. d. 232.65 V d. 6.05, 17.8 A d. 4,985 W a. 236.98 V 20. Referring to problem 19, find a. 6, 17.9 A 21. Referring to problem 19, find a. 4,464 W b. 234.76 V c. 240 V the current of each generator in amperes b. 5.82, 18 A c. 6.34, 17.5 A the total power in watts b. 5,792 W c. 5,616 W