B1 a) b) c) The simply supported beam in Fig QB1a is made by gluing two pieces of wood of rectangular cross-section as shown in Fig QB1b, i.e. the top board (flange) is glued onto the bottom board of the web. The supports at A and B exert only vertical reactions. 150mm y 30mm A 4m C 30mm 150mm 6.5 kN/m Fig QB1a 4m B y = 0.120m Fig QB1b Calculate the support reaction forces, and hence sketch shear and bending moment diagrams indicating the values at A, B, C. Describe how shear force and bending moment vary along the beam; Compute the moment of inertia of the section about the neutral axis. The position of the neutral axis is y = 0.120m as shown in Figure QB1b; Determine the maximum shear stress in the glue necessary to hold the beam together along the seam where they are joined.

B1 a) b) c) The simply supported beam in Fig QB1a is made by gluing two pieces of wood of rectangular cross-section as shown in Fig QB1b, i.e. the top board (flange) is glued onto the bottom board of the web. The supports at A and B exert only vertical reactions. 150mm y 30mm A 4m C 30mm 150mm 6.5 kN/m Fig QB1a 4m B y = 0.120m Fig QB1b Calculate the support reaction forces, and hence sketch shear and bending moment diagrams indicating the values at A, B, C. Describe how shear force and bending moment vary along the beam; Compute the moment of inertia of the section about the neutral axis. The position of the neutral axis is y = 0.120m as shown in Figure QB1b; Determine the maximum shear stress in the glue necessary to hold the beam together along the seam where they are joined.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question
Q1: Specify the type of the truss shown in Fig.(1). Then, find the forces in bars FJ and JH. كومبلكس معقد x؟ 3,0 3.0 A VER B E 60KN 60KN 42.02.03.02.2.0 بدع
Example 6.14. The central bottom chord member of roof truss is 4 m long, carries an arial tension 250 kN and supports a moveable differential chain hoist of 4 kN capacity including impact The member is composed of 2 angles 100 mm × 75 mm X 10 mm @ 13 kgim with the longer legs up and placed back on either side of 10 mm gusset plates. The outstanding shorter lees at the bottom provide necessary track for the hoist. The angles are tack riveted at 1 m centers with 20 mm dia, rivets. Check the efficiency of the section provided. The permissible tensile stress in axial tension and bending are 150 MPa and 165 MPa respectively. The permissible stress in N/mm, subject compression for flangeless beams unsupported laterally may be taken as 3300 /b 10 a maximum of 140 N/mm, where 1= unsupported length of the member and b is the combined thickness of the angles.
Joints I,J,K,L,Q and M of the frame shown in the figure (not drawn to the scale) are pins. Continuous members IQ and LJ are connected through a pin at N. Continuous members JM and KQ are 10 kN 10 kN 10 kN Im connected through a pin at P. The frame has hinge supports at joints R and S. The loads acting at joints I, J and K are along the negative Y direction and the loads acting at joints L and M are along the positive X direction. 1m L 10KN O „ImIm1m1m lmlm M 10KN The magnitude of the horizontal component of reaction (in kN) at S, is
Determine (approximately) the forces in the members of the truss shown in Fig. 7-2a. The diagonals are to be designed to support both tensile and compressive forces, and therefore each is assumed to carry half the panel shear. The support reactions have been computed. 20 kN F 3 m A 10 kN -4 m E 20 KN 4 m. D C 10 KN
Q1) The forces F1,F2 and F3, all of which act on point A of the bracket, are specified in three different ways determine the x and y scalar component of each of the three forces show in the Fig (1)? F2-500N 0.2m F3-800 N 0.4m F1-600N o.1 m B 0.3 m
Classify the truss show in in Fig. as .3 statically determinate, statically * indeterminate, stable or unstable E B C A unstable O stable, Statically determinate O stable, Statically indeterminate to the 6 degree stable, Statically indeterminate to the 3 degree O أخرى
Determine the forces in members FJ; HJ, and HK of the K truss shown in Fig. 4.24(a) by the method of sections.
Question 5 a) What is the importance of SFD and BMDs for structural engineers? b) For the beam and loading shown in Fig 5-1. i. iii. 2 kN/m -3 m- Figure 5-1 4 kN/m 1.5 m- B Page 5 of 6 Determine the support reactions at A. Draw the shear force diagrams (SFD), clearly indicating the shear force along the span at AB. Draw the bending moment diagrams (BMD), clearly indicating the moments along the span AB.
Cross bracing is used to provide lateral support for this bridge deck due to the wind and unbalanced traffic loads. Determine (approximately) the forces in the members of this truss. Assume the diagonals are slender and therefore will not support a compressive force. The loads and support reactions are shown.
Using method of joints
Question 5 a) What is the importance of SFD and BMDs for structural engineers? b) For the beam and loading shown in Fig 5-1. i. iii. 2 kN/m -3 m- Figure 5-1 4 kN/m 1.5 m- B Page 5 of 6 Determine the support reactions at A. Draw the shear force diagrams (SFD), clearly indicating the shear force along the span at AB. Draw the bending moment diagrams (BMD), clearly indicating the moments along the span AB.