S1) just Solve B 1. An ATMega 32 microcontroller, as shown in the figure below,continuously receives two inputs from the bottom 4 bits of ports B and Aand calculates the product of these two numbers as unmarked (M = A *B), then the output of the product multiplied by (M ) Sends to port C.A) Write a subroutine that performs the desired multiplication with thehelp of the multiplication commandB) Write a subroutine that performs the desired multiplication with thehelp of the reference table.C) With the help of one or two written subroutines, write a program thatcontinuously, the value of M is greater than 100, the LED is HIGH and ifit is less than 50, the LED is Low.ATmega32PBРА40383736353433323130292827262524232221A1011121314151617181920HighPD.0M270PD.2270y#LowPC12345

MOVE R1,-(SP) MOVE R2,-(SP) CALL LISTMULTIPLY MOVE 1(SP),R0 ADD #2,SP

Answered: B) Write a subroutine that performs the…

Engineering

Computer Science

B) Write a subroutine that performs the desired multiplication with the help of the reference table.

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter2: Introduction To Systems Architecture

Section: Chapter Questions

Problem 2VE: A(n) __________ is a storage location implemented in the CPU.

See similar textbooks

Similar questions

A set of ten packed BCD numbers is stored in the memory location starting at 3050H. i. Write a program with a subroutine to add these numbers in BCD. If a carry is generated, save it in register B, and adjust it for BCD. The final sum will be less than 9999sCD. ii. Write a second subroutine to unpack the BCD sum stored in registers A and B, and store them in the memory locations starting at 3070H. The most significant digit (BCD4) should be stored at 3070H and the least significant digit (BCD) at 3073H.
Q1- Write a program in assembly language for the 8085 microprocessor to receive 10 bytes of data via the SID and store it at the memory address (3000H to 3009H) using a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz. When you receive each byte of the required bytes, you must adhere to the following: The bits of two high bits will be received at the beginning of the reception (start bits), after that the data bits will be received, after that the low bit of the stop bit will be received (stop bit). The following flowchart will help you, but you should notice that this flowchart deals with one byte, and you are required to deal with 10 bytes The solution must be integrated and include the calculation of the baudrate delay time Of+CD!HID+[00 Yes SIDATA Read SID Start Bit? Wait for Half-Bit Time Set up Bit Counter Wait Bit Time Read SID Save Bit Decrement Bit Counter All Bits Received? Add Bit to Previous Bits Go Back to Get Next Bit Return IMUNI
Q2- Write a program in assembly language for the 8085 microprocessor to receive one byte of data via the SID and store it at the memory address (3000H to 3009H) using a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz . When receive the required bytes, you must adhere to the following: The bits of two high bits will be received at the beginning of the reception(start bits 1 1 ), after that the data bits will be received, after that the low bit of the stop bit will be received (stop bit 0 ). The following flowchart will help you. The solution must be integrated and include the calculation of the baudrate delay time
mikroPascal Pro for PIC Microcontroller program in Pascal help.
(d) The table below shows the ALUcontrol signal of the datapath we discussed in class. Instruction Funct ALU Орсode ALUop ALU action operation field control Iw 00 load word XXXXXX add 0010 Sw 00 store word XXXXXX add 0010 beq 01 branch equal subtract 0110 XXXXXX R-type 10 add 100000 add 0010 R-type 10 subtract 100010 subtract 0110 R-type 10 AND 100100 AND 0000 R-type 10 OR 100101 OR 0001 R-type 10 set on less than 101010 set on less than 0111 You want to add the bne instruction into the datapath, which already includes the required hardware for the instruction. Write out the ALUop for bne and how you can determine whether the bne results in the branch to be taken.
a. Find the address accessed by each of the following instructions. If DS = 0100H, BX= 0120H, DATA = 0140H, and SI = 0050H and real mode operation:1. MOV DATA[SI], ECX2. MOV BL, [ BX+SI]b. Descriptor contains a base address of 00260000H, a limit of 00110H, and G = 1,determine starting and ending locations are addressed by the descriptor for aCore2.
25: . Find the time delay in the following program if the crystal frequency is 1 MHz. Do not ignore the time delay due to the first and last instruction. DELAY: LDI R16, 30 AGAIN: LDI R17, 35 HERE: NOP NOP DEC R17 BRNE HERE DEC R16 BRNE AGAIN RET 26: Write a program to display 2 on 7 segment. A 7 segment is connected to PortD.
LIST P = 16F877AUsing INCLUDE "P16F877A.INC" and PWM (Pulse Width Modulation), write the microprocessor code that enables the fan to operate at 80% if the button on the 5th bit is pressed, and 30% if the button on the third bit is pressed.
26. Find the time delay in the following program if the crystal frequency is 1 MHz. Do not ignore the time delay due to the first and last instruction. DELAY: LDI R16, 30 AGAIN: LDI R17, 35 HERE: NOP NOP DEC R17 BRNE HERE DEC R16 BRNE AGAIN RET
Microprocessor assembly code: There are 25 1-band numbers stored in memory starting from 1000H address. Write the program that shows the numbers greater than 50 with LEDs connected to port 2 with 2s intervals Tips: If the numbers are 01-03-55-21-51-34 ...... 66-FF 55-51 -..... 66-FF will be sent to Port 2 at 2s intervals. It should be assumed that the numbers were pre-entered into memory with the C 1000 command.
Q11. Write a program to exchange BC & DE register pair using Intel 8085 CPU stack. Q12. Say what the following program does: Start: LDA 4000H LOOP: ADD А, А CPI EFH JC LOOP STOP: STA 4000H HLT
8086 microprocessor