b) The old Hydraulics laboratory in Mechanical Engineering used a roof tank to supply apparatus with water at a nearly constant head. The water was collected in an under floor sump, and then pumped back to the roof tank after the experiment. The flow rate was 10 litre s1. The tank was 6m above the sump, and the length of the pipe route was 15 m. The old 6" pipes are now heavily corroded (k = 7.5 mm). The old pump has been scrapped. What head AH would be specified for a pump to restore the system using the old pipes? What would the pump power be? If the pipes were replaced with 150 mm diameter PVC pipes, what pump AH would be required? ROOF TANK 6m PUMP SUMP

b) The old Hydraulics laboratory in Mechanical Engineering used a roof tank to supply apparatus with water at a nearly constant head. The water was collected in an under floor sump, and then pumped back to the roof tank after the experiment. The flow rate was 10 litre s1. The tank was 6m above the sump, and the length of the pipe route was 15 m. The old 6" pipes are now heavily corroded (k = 7.5 mm). The old pump has been scrapped. What head AH would be specified for a pump to restore the system using the old pipes? What would the pump power be? If the pipes were replaced with 150 mm diameter PVC pipes, what pump AH would be required? ROOF TANK 6m PUMP SUMP

Name: hydraulics b) The old Hydraulics laboratory in Mechanical Engineering
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: hydraulics b) The old Hydraulics laboratory in Mechanical Engineering used a roof tank tosupply apparatus with water at a nearly constant head. The water wascollected in an under floor sump, and then pumped back to the roof tankafter the experiment.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What is hydraulic head?
Select the two seals used to sealing active elements of a pump or compressor to retain the pumped fluid: U-cup O-rings V-packing piston rings face seals lip seal
Industrial Main What causes pressure in a hydraulic system?
The fluid leaves the impeller with more velocity head Select one: True False
what is the difference between the terms fluid power and hydraulics and pneumatics?
8.Which of the following pairs is high pair? A sliding pair В cam pair C screw pair
40) Technician A says Pascals law can be used to provide mechanical advantage. Technician B says a single hydraulic system is capable of providing different amounts of output pressures from a common system pressure. Which technician is correct? O Technician A O Technician B O Both technicians A and B O Neither technician A nor B
For a quick movement hydraulic system is more suitable than pneumatic system. Select one: True False
Which of the following statements are true for accumulator used in hydraulic systems? 1. Accumulator stores fluid with pressure 2.Accumulator stores fluid without any pressure 3. Accumulator stores compressible liquid 4. Spring is used as an external source to keep the fluid under hydraulic pressure Select one: O a. 1,3 and 4 O b. 2 and 3 O c. 1 and 4 O d. 2,3 and 4
Which of the following is NOT one of the four criteria by which the size of a hydraulic reservoir is determined? O Its inner surface must be covered with a layer of stainless steel to avoid corrosion It must have a surface area large enough to dissipate heat It must maintain oil level high enough to prevent a whirlpool effect at the pump inlet It must make allowance for dirt and chips to settle and air to escape
Which of the following is NOT one of the seal types used in hydraulic systems? O Piston cup packings O-ring Piston rings O V-ring packings O All of these are seal types used in hydraulic systems
ASAP