Answered: B- the eddy current losses of 400V, 50…

B- the eddy current losses of 400V, 50 Hz transformer is 1600W and the total iron losses i 2500W. calculate the iron losses at 200V, 25 Hz.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.11MCQ: For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the...

See similar textbooks

Related questions

Q: What is the benefit of the electrical transformer in the case of load and in the case no load?

A: Discuss the benefit of the electrical transformer in the case of load and in the case no load?NoteA…

Q: The resistance and reactance of the primary winding of a 440/110 V single phase transformer are 4.4…

Q: The amount of inrush current in the primary of a transformer is limited by the........, A- amount of…

Q: A transformer with a 10/1 turns ratio has a maximum flux density of 60,000 lines/in2, when the…

A: EMF E = 4.44×frequency×Flux in the core×per phase turns. But flux = flux density× area of the core.…

Q: A voltage transformer in Figure 8 has 1,500 turns of wire on its primary winding and 500 turns of…

A: The number of turns on the primary side, The number of turns on the secondary side, The voltage…

Q: How do you calculate N1/N2? Ratio of primary to secondary turns of a transformer?

A: It asked how to calculate the ratio of primary to secondary turns of a transformer.

Q: A 400/800 ratio transformer has secondary winding resistance of 0.5 ohm. What is the total…

A: Total resistance referred to primary side = Secondary winding resistance×primary voltagesecondary…

Q: Which of the following statements is true about an ideal transformer? O It changes the magnitude of…

A: Choose the correct option Which of the following Statments is true about an ideal transform.

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

B- the eddy current losses of 400V, 50 Hz transformer is 1600W and the total iron losses i
2500W. calculate the iron losses at 200V, 25 Hz.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
A single-phase step-down transformer is rated 13MVA,66kV/11.5kV. With the 11.5 kV winding short-circuited, rated current flows when the voltage applied to the primary is 5.5 kV. The power input is read as 100 kW. Determine Req1andXeq1 in ohms referred to the high-voltage winding.
For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is referred to winding 1 (primary) by multiplying Z2 by (a) The turns ratio (N1/N2) (b) The square of the turns ratio (N1/N2)2 (c) The cubed turns ratio (N1/N2)3
An ideal transformer has no real or reactive power loss. (a) True (b) False
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
A 400/800 ratio transformer has secondary winding resistance of 0.5 ohm. What is the total resistance in ohmsreferred to primary?
The amount of inrush current in the primary of a transformer is limited by the........, A- amount of applied voltage, B- resistance of the wire in the primary winding, C- flux change of the magnetic field in the core, D - all of the above What precaution must be observed when working whit current transformers? A- never have a load on the secondary, B- always ha a load on the secondary, C- de-energize the primary whenever there is a load on the secondary, D - none The fact that the movable coil of a constant-current transformer moves further away from the stationary coil with a increase in load current is based on which fundamental priciple of magnetism? A- like magnetic poles attract, B- like magnetic poles repel, C- the amount of current flowing through a coil inverdely proportional to its flux density. D- none
The equivalent resistance of the primary of a transformer having K = 6 and R1 = 0.2 ohm when referred to secondary becomes.......ohm. Group of answer choices 0.004 7.2 0.72 0.0055
How do i calculate secondary current in transformer analysis
Which of the following are power losses that can occur in a practical transformer (non-ideal)? copper loss O loss due to eddy currents V hysteresis loss O voltage drop due to coil material
The core of a transformer operating at 50 Hz has an eddy current loss of 100 W/m3 and the corelaminations have a thickness of 0.50 mm. The core is redesigned so as to operate with the same eddycurrent loss but at a different voltage and at a frequency of 250 Hz. Assuming that at the new voltage themaximum flux density is one-third of its original value and the resistivity of the core remains unaltered,determine the necessary new thickness of the laminations. Clear and detailed solution.