(b) Mr. Musa Al Biruni is analyzing a 100 kVA, 60 Hz, 7200-48ov, single phase transformer, which has the following parameters expressed in ohms; R-3.06, XHS-6.05, Xus=17809, R-0.014, X-0.027, R-71400 The transformer is supplying a distribution side load that draws a rated current at 480V and 75 percent power-factor lagging. Sketch the appropriate equivalent cireuit and determine (a) the equivalent resistance and equivalent reactance referred to high side (b) the input voltage to the transformer (c) the exciting current and its core loss and magnetizing components

(b) Mr. Musa Al Biruni is analyzing a 100 kVA, 60 Hz, 7200-48ov, single phase transformer, which has the following parameters expressed in ohms; R-3.06, XHS-6.05, Xus=17809, R-0.014, X-0.027, R-71400 The transformer is supplying a distribution side load that draws a rated current at 480V and 75 percent power-factor lagging. Sketch the appropriate equivalent cireuit and determine (a) the equivalent resistance and equivalent reactance referred to high side (b) the input voltage to the transformer (c) the exciting current and its core loss and magnetizing components

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Draw a block diagram of a power supply from transformer up to regulator with corresponding waveform.
A Cock-croft Walton type voltage multiplier has 7 stages with capacitance all equal 0.07pF. The supply a frequency of to be supplied is 6.5mA. to transformer secondary voltage is 133kV at 250HZ. If the load current The total voltage ripple of the system is: (a) 15.3kv (b) 12.2kv (c) 9.1kV (d) 10.4kv (e) 1.9kv a. d O b. a OC C O d. e O e. b
Ql-phase step down transformer 1250 KVA, 10002200 V, 50 Hz The resistance /phase and leakage reactanceiphase of the primary winding are 0.78 2 and 4.82 and the corresponding values for the secondary winding are 0.012 and 0.002 respectively if the primary winding is connected in delta and secondary in star calculate: )The voltage to be applied at normal frequency to the primary to circulate full-load through it when the secondary is short-circuited li) The full load copper loss
4. 100 kVA, 6800-240 V, 50 Hz single phase step down transformer has the following parameters: RIs=0.0082 Rus=2.62 Rfc-HS=5000n XLs=0.0152 Xus=5.2 XmHs=88002 Transformer is delivering 80% of rated load at rated voltage and 0.95 lagging power factor. Determine the following: a) The equivalent impedance of the transformer referred to primary. b) Input impedance of the combined transformer and load. c) Actual input voltage at HV side. d) Input impedance if load is disconnected. e) Exciting current at no load.
A single phase transformer has a 600 turns in the pri- mary and 1200 turns in the secondary. The cross sec- tional area of the core is 905 sq.cm. If the primary winding is connected to a 50 Hz supply at 400V. The peak flux density is wb/m²
In part c determine the voltage across Rp and Xp .
A short transmission line connects a step-up transformer on the source side with a series impedance of j0.5 ohms (referred to the primary) to a step-down transformer on the load side with a series impedance of 50 ohms (referred to the primary). The turn ratio of the step-up transformer is 1:10 and a no-load primary voltage of 23 (line-to-line) kV. The step-down transformer has a turn ratio of 35:2 and it has a Y-connected, balanced load of 0.490 +j 0.0816 ohms connected to its secondary side. A capacitor bank of -j0.171 ohms is added parallel to the load. Assuming an ideal transmission line, the load voltage (line-to-neutral) would be: O A. 7360 V O B. 6.2 kV O C. 12750 V O D. 4806 V O E. None of the other choices are correct
NEAT EXPLAIN NEEDED( CORRECT ANSWER NO GPT PLEASE)