b) For water you obtained the following data: Temperature [K] 300 310 318 340 Viscosity [cP] 0.8509 0.6913 0.5958 | 0.42 What is the viscosity of water at 314 K ?:

Q: 6 - From the question (5) find the real length of the line AB. *

A: the real length of line AB

Q: A 3/4-in.-diameter hole is drilled in a piece of 1-in.-thick steel; the hole is then countersunk as…

A: The required volume of the given hole is obtained by rotating the area shown about the Y-axis.

Q: The dot product of two unit vectors: (The answer cannot be found on the other choices.) always has a…

A: When the dot product of any two vectors is equals to 1 then those vectors are in same direction…

Q: Q243 For the force system shown in figure C24); determine The magnitude and location of the…

A:

Q: What is the solid area’s second moment about the Y-axis

A: according to the given details in the question.

Q: (Determine the (f_y ) when force 80 Ib and angle 30° on the axis (X .A 40 .B 40lb .C 4lb .D 40N

A:

Q: The region bounded by the parabola x = y² and y = x2 revolved about the y-axis to generate a solid.…

A:

Q: 3.00- 1.25-

A:

Q: PO 8 in.

A: Redraw the following figure for the given question.

Q: Q3/ For the plate shown in figure below find (a) E A Y수 4 6 X 7 5

A: Let us consider the given figure , divide into two parts of area A1 and A2 The sum of area ΣA can be…

Q: 4 = 2, B= 3, and the angle formed by A and B is 60°. Calculate the value of 4+ 2B. Round your answer…

A:

Q: h a 60° 60° --X

A: Let’s divide the shaded area into two parts. Section 1 is a triangle OAB and Section 2 is a circular…

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: find Q ? L 7om dsolm Lsioum L. 2om f=0002

A: Velocity of flow at entry of 100 m pipe, v=2gh where, h=height of reservoir=8m Therefore velocity,…

Q: nd the Zero member enlys 3 3. 3. D. 3. 3. 8m

A: given; find zero force member only

Q: In the picture, a weight pulls on a pulley (solid disk) of mass 0.5kg and a radius of 0.25m. The…

A:

Q: Q1) Find the distance of resultant from point(a). 20N -3m. 140 30N 30 15N

A:

Q: H G 60 E D 7 kN 7 kN 9 kN 6m 6m 6m 6m

A:

Q: y 4+B 5+C 2 3. 1.Find The size of the area number 1 (triangle) 2.Find The center of the numbered…

A: Given data: h1=3+Ab1=4+B Need to determine the centroid and area of the shape 1.

Q: 4. What is the complement of a 72°21'47" angle?

A: We know that the complement angles pair have sum = 90o let x =  72o 21' 47"  (Given) Complement of x…

Q: 21 Given, z1=2+3j and z2=3-4j, determine the argument in two decimal places of the resulting value…

A: Given:z1=2+3jz2=3-4j

Q: (b) Find F2-2 for the two-dimensional geometry. Aq is a square (A, refers to the total area of the…

A: Shape factor: When radiation is examined between two entities at two distinct orientations, the…

Q: 400 Ib 14' A 60° 450 Determine the Value of P

A: given data: let  RA=normal reaction force at ARB=normal reaction force at B AC=4' CD=14' DB=2'

Q: Which of the points is located in the third quarte

A: Given Points To find Points located in third quarter

Q: 600 N F1 12 200 N 30° F2 3.

A:

Q: Find the resultant and angle of direction based on the horizontal. using tail to tip method 1. 43…

A: According to the details provided in the question, we need to calculate RESULTANT AND ANGLE

Q: Re = 63 * lo4 if the = 0.25 Re = 63 * De termine ? 169

A:

Q: express this in cosine form

A: Giveny=-10sinωt+120

Q: Given two points; (4,17) and (-4,1) on a line, what is the slope of the line? A. 2 B 1/2 C 1/2 D 2

A: Given Data A(4,17) B(-4,1)

Q: 5. The rectangular components of force are respectively. 220° 100 N (a) -100 sin 220°, –100 cos 220°…

A: As we know, there are four quadrants: I, II, III, IV. In the first quadrant, x and y-axis are…

Q: Isn't the area of the circle equal to pi times the square of its radius?

A: Explanation: Since the diameter ( d )  of steel bar is given, area of the circle is in terms of…

Q: 11 The volume of a cube with sides of L is L. If the length is measured as 121 +2 mm, determine the…

A: Given data  The length measurement = 121+/-2 Find the worst possible error in the volume

Q: Figure 4 shows the block diagram of a mechanical system. Given m3=3 Kg; m2=4 Kg; B1=5 N-s/m; B2=6 N-…

A:

Q: x2(1) x1(t) K fv, M2 f(t) M1 fv, fv. fv,

A:

Q: Question 3) The length L is given as L=34 m on the plate in the figure. According to this; Question…

A:

Q: OO O Question No. 10 If the sum of two numbers is 55 and the H.C.F. and L.C.M. of these numbers are…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.