(b) Find F2-2 for the two-dimensional geometry. Aq is a square (A, refers to the total area of the four sides) and A2 is part of a circle. 30 30

Q: What are internal forces?

A: Internal forces are defined as the forces exerted by the particles of the body on each other within…

Q: For the stress element below, when a = 6, b = 4, and c = 6, the principal stress σ1 , the largest…

A:

Q: 2.34 Determine the resultant of the three forces of Prob. 2.22. Answer

A: Given:The three forces are:F1=800 NF2=408 NF3=424 N

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for each…

A: Consider a vehicle engine where number of cylinder are situated whose bore diameter is D and stroke…

Q: If A=0.375 inch, B=0.923 inch, C=1.0992 inches, find G A 기사 W -|×|-> G- -B- -C- F E-

A: If A= 0.375 inch, B=0.923 inch, C=1.0992 inches,find G.

Q: The triangular lamina with base = 80 mm, height = 60 mm.  The Iyy value is _____________ mm4 Select…

A: Given data: base (b) = 80 mm height (h) = 60 mm Need to determine the moment of inertia about y-y…

Q: 1. The built-up beam pictured on the right is subjected to an internal moment of M = 75 kNm. a) At…

A: *The internal moment acting on the structure is M=75 kNm. *The total length of the T section is…

Q: Wind flows over a flat plate of length L = 25 mm and width W = 8 mm. The plate is maintained at a…

A:

Q: Degree of drawing is measured in terms of; Reduction in strain Reduction in area O Reduction in…

A: Degree of drawing is measured in terms of: Answer: Reduction in area

Q: wy = 1/2 Wy= 98 V = TT R = 4500 by = 0.12346 wx= 102.66 Mechanical V = 2000 x 1000 360 SSS.S کککک…

A:

Q: Customary units by using the values listed for length and mass as defined values: Bending moment or…

A: As moment bending moment or torque has two variables, force and distance. So, M = F × r…… (1) The SI…

Q: Figure Q4 shows the values of the normal and shear stresses acting on a certain stress element which…

A: Given: Normal Stress in x direction→σx=-1.5 MPa Normal Stress in y direction→σy=1 MPa Shear stress…

Q: Determine the x, y, z components of reaction at the thrust bearing D 0 = 0°.

A:

Q: Assume oz = 500, ay = 300, Txy = 250, oyicld = 350. Answer the following questions. Click here for…

A: GIVEN DATA σx= 500MPa σy= 300MPa τxy= 250MPa We have to find maximum and minimum normal stress on a…

Q: A force F = 6980 N acts upon a piston head, as shown in the figure. The gudgeon pin G connects the…

A:

Q: What is the average shear stress?

A:

Q: The impact test is used to find a material's it's ability to absorb energy before it fractures. O.…

A: About impact test. Impact test is used to determine the dynamic toughness material. In this test a…

Q: 150 m 50 mm 85 mm Section X-X 20 kN

A:

Q: 0.250 DRILL THRU SIX HOLES EQUALLY SPACED 23° 30° CYLINDRICAL PLATE 1" STD 8 PIPE 3" XS BI PIPE 3"…

A: Section A-A represents the following thing.

Q: name these lines

A: The names of the given lines is given below.

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provide resistance in changing its state of velocity or motion for coming to a state of rest. In other words, Newton's first law of motion describes the law of inertia of a rigid body.