5. (a) For perfectly plastic direct impact, show that total kinetic energy of the system remainedconserved.(b) Define critical speed. Show that the critical speed of a shaft is same as the natural frequencyof free transverse vibration.

THIS IS A SOLUTION OF PART B CRITICAL SPEED OF SHAFT In strong mechanics, in the field of…

Answered: (b) Define critical speed. Show that…

(b) Define critical speed. Show that the critical speed of a shaft is same as the natural frequency of free transverse vibration.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 3.2, don’t do any other question, just problem 3.2
ي
8.9 (A/B). A solid steel shaft of 200 mm diameter transmits 5 MW at 500 rev/min. It is proposed to alter the horsepower to 7 MW and the speed to 440 rev/min and to replace the solid shaft by a hollow shaft made of the same type of steel but having only 80% of the weight of the solid shaft. The length of both shafts is the same and the hollow shaft is to have the same maximum shear stress as the solid shaft. Find: (a) the ratio between the torque per unit angle of twist per metre for the two shafts; (b) the external and internal diameters for the hollow shaft. [L.Mech.E.] [2.085; 261, 190 mm.]
In a gear box input torque is measured to be 1 kNm at a speed of 1440 rpm. Gear box has unknown arrangement of gears inside. But the output shaft rotates at 840 rpm in direction opposite to input shaft. If the efficiency of transmission is equal to 93%, torque required to hold the gear box will be equal to (a) 2594 Nm in the direction of rotation of input shaft (b) 2594 Nm in the direction of rotation of output shaft (c) 549 Nm in the direction of rotation of input shaft (d) 549 Nm in the direction of rotation of output shaft
Can someone please help me to answer the following question completely. PLEASE AND THANK YOU!!!
A single solid circular shaft 400 mm diameter running at 250 RPM, is to be replaced by two hollow circular shafts of equal size running at 150 RPM and developing 50% additional power. The internal diameter of hollow shaft may be taken as one third of their external diameters. If the working stress of the new shaft is 30% greater than that of the former, find the external and internal diameter of hollow shafts.
The shaft shown in the ﬁgure is machined from AISI 1040 CD steel. The shaft rotates at 1600 rpm and is supported in rolling bearings at A and B. The applied forces are F1 = 1600 lbf and F2 = 640 lbf. A steady torque of 1600 lbf·in is being transmitted through the shaft between the points of application of the forces. ——————————————- Determine the endurance limit for this material as well as the value after correction for surface finish, sizing, and loading. (You must provide an answer before moving to the next part.) The endurance limit for this material is kpsi. The value after correction for surface finish, sizing, and loading is kpsi.
2. Determine the blade radius, twist and chord distributions for a 2-bladed rotor that will produce a rated power 150 kW.
Please design the following mechanical shaft targeting design objective of reliable structure and performance via design iterations with constrains of geometrical dimensions within performance requirement, safety, and economic factors (finding minimum material cost of suitable diameter). Notes: This shaft is transmitting 200 kW at 1200RPM. Please design the shaft with a suitable diameter via iterations, if the maximum torque transmitted exceeds the mean by 30%. Take maximum allowable shear stress as 70 MPa.
2. A 1020 CD steel shaft (Sy=390 MPa) is used to transmit 20 kW of power at 1200 rpm. There are no bending or axial loads on the shaft. It is desired to have a static factor of safety of 2 based on the Distortion Energy theory. Determine the minimum diameter needed for the shaft. Power, P= To Pure torsion, relationship between T and t Torsional stress
5- Please I want answer of this question. Thanks