(b) Assuming the op-amp is ideal, refer to the circuit in Figure 5.2 to answer the questions below.2 k28 k25 k2Vb3 V4 k210 k2Fig 5.2: Circuit for question 6b(i) Determine the value of ig, i.e. the current enters the inverting input of the op-amp.(ii) Determine the value of vp.(iii) Determine the value of current passing through 2 kN.(iv) Determine the value of vo-(v) Determine the value of io.

Answered: Image /qna-images/answer/a3e7f4c1-1b5e-4eea-ad1b-360370c8ea63.jpg

(b) Assuming the op-amp is ideal, refer to the circuit in Figure 5.2 to answer the questions below. 2 k2 8 k2 5 k2 Vb 3 V 4 k2 10 kN Fig 5.2: Circuit for question 6b (i) Determine the value of i, i.e. the current enters the inverting input of the op-amp. (ii) Determine the value of vp. (i) Determine the value of current passing through 2 kN. (iv) Determine the value of vo. (v) Determine the value of io.

(b) Assuming the op-amp is ideal, refer to the circuit in Figure 5.2 to answer the questions below. 2 k2 8 k2 5 k2 Vb 3 V 4 k2 10 kN Fig 5.2: Circuit for question 6b (i) Determine the value of i, i.e. the current enters the inverting input of the op-amp. (ii) Determine the value of vp. (i) Determine the value of current passing through 2 kN. (iv) Determine the value of vo. (v) Determine the value of io.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the ideal op-amp shown, what should be the value of resistor Rf (in kilo Ohms) to obtain a gain of 55? No need for a solution. Just write your numeric answer (without the unit) in the space provided. Round off your answer to 2 decimal places.
For the circuit, assuming an ideal op amp, and given Vs = - 1.5 V, R1 = 1 K ohm, R2 = 15k ohm, and R3 = 5k ohm, answer the following question. (Annotate diagram to show branches and nodes.) (a) Find the currents in all the branches (b) Find the voltages at all nodes (c) Find the power dissipated in each resistor (a) Find the total power dissipated in all resistors (e) How much power is delivered by Vs? (f) Explain: where does the rest of the power come from?
A non-inverting op-amp circuit has the open loop gain of 116 and the resistances R1=2400 n and R2 = 5.8 ka . Calculate (a) The actual value of voltage gain (b) Considering the finite open loop gain, the ideal value of gain (C) Error, when ideal voltage gain is compared with actual voltage gain (d) The percentage error, when ideal voltage gain is compared with actual voltage gain. (a) The actual value of voltage gain (b) The ideal value of voltage gain (c) Error, when ideal voltage gain is compared with actual voltage gain. (d) The percentage error, when ideal voltage gain is compared with actual voltage gain.
Practise 1
The op amp in the circuit in is ideal. Part A What op amp circuit configuration is this? ANSWER: v₂ = A difference amplifier circuit. An inverting summing amplifier. A non-inverting summing amplifier, R Part B Find an expression for the output voltage v, in terms of the input voltage v. Assume that is in volts. Suppose Ry = 20 kn. Express your answer in terms of V. ANSWER: V Part C Suppose v₁ = 2 V. What value of Ry will cause the op amp to saturate? Express your answer to three significant figures and include the appropriate units. ANSWER: 21 5 kn w 8 k 9-67-5 2 V m 10 V -10 V 27 k
The op-amp shown is non-ideal, having an open loop gain of only 100. All its other characteristics however are ideal. What is the actual gain v₁/v₁ of the op-amp if R = 4.1 KQ. Express your answer in KQ accurate to two decimal places. 1K www R www + Vo
it's urgent please solve asap
A generic op-amp circuit is shown in Figure 3. With the given data, answer the following by showing the corresponding circuit and by explaining your answer or presenting the solution. a. If VA=0, VB=1V, RA=RB=10k2, R1=70KSN, R2=0 and vout=8V, which terminal (A or B) is the noninverting input? b. If VA=10, VB=0V and B is the inverting input, select RA, RB, R1, and R2 and to obtain an output voltage of 20v. c. If VA=VB=1V, R1=0, R2=0 and vout=1V, which terminal (A or B) is the inverting input? R2 VA RA А O Vout RB B VB RI
The input resistance of the circuit shown in the figure assuming an ideal op amp, V₁. Lien 2R + 3R Vo
Part A - Calculating the output voltage of a difference op-amp circuit Learning Goal: To analyze difference op-amp circuits. Before proceeding, review difference op-amp circuits and the For the circuit shown (Figure 1), determine Vo when R = 9,6 kN. R, = 40 kN. V. = 10 mV. V. = 40 mV. and Ve =5 V ideal op-amp assumptions. Express your answer to three significant figures and include the appropriate units. > View Available Hint(s) HẢ ? Vo = Value Units Submit Part B - Design of a difference op-amp circuit For the circuit shown (Figure 1), determine R1 such that Vo = m x (Vz - Vy) - Assume m = 4.5 and R2 = 30 kn and that the op-amp is in its linear region of operation. Figure Express your answer to three significant figures. > View Available Hint(s) R2 Πνα ΑΣφ It vec ? R1 R = -Vcc V. Submit Provide Feedback Next > Dearson
A certain op-amp has three internal amplifier stages with midrange gains of 30 dB, 40 dB, and 20 dB. Each stage also has a critical frequency associated with it as follows: fc1 = 600 Hz, fc2 = 50 kHz, and fc3 = 200 kHz. (a) What is the midrange open-loop gain of the op-amp, expressed in dB? (b) What is the total phase shift through the amplifier, including inversion, when the signal frequency is 10 kHz?
Perform the block diagram given on the side using an op-amp.