(b)A three-phase, 50 Hz, four poles induction motor runs at a no-load speed of 1350 r/min andfull-load speed is 1200 r/min.(i) Calculate the slip of the rotor at no-load and full-load conditions.(ii)Based on Q1(b)(i) results, calculate the electrical frequency of the rotor no-loadand full-load conditions.(iii) Calculate the speed regulation of this motor.

This question belongs to electrical machine . It is based on the concept of slip of induction motor…

(b) A three-phase, 50 Hz, four poles induction motor runs at a no-load speed of 1350 r/min and full-load speed is 1200 r/min. (i) Calculate the slip of the rotor at no-load and full-load conditions. (ii) no-load Based on Q1(b)(i) results, calculate the electrical frequency of the rotor and full-load conditions. (iii) Calculate the speed regulation of this motor.

(b) A three-phase, 50 Hz, four poles induction motor runs at a no-load speed of 1350 r/min and full-load speed is 1200 r/min. (i) Calculate the slip of the rotor at no-load and full-load conditions. (ii) no-load Based on Q1(b)(i) results, calculate the electrical frequency of the rotor and full-load conditions. (iii) Calculate the speed regulation of this motor.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2 Complete the answer : The rotor reactance of the three phase induction motor is varies with ................... of the rotor current.
With the aid of diagrams describe the basic topology of a wound field 3 phase synchronous generator and outline the relationship between the excitation voltage and rotor current. Q2 (a) (b) Outline with the aid of a suitable diagram the necessary power conversion stages required to interface a small permanent magnet (PM) generator to a stand alone DC system. A star connected 3 phase wound field synchronous generator with a synchronous reactance of 20 N is connected to a 6.6 kV (phase voltage) grid and supplies 1.5 MW at 0.95 lagging power factor at its terminals. Calculate the phase current and resultant voltage across the synchronous reactance (Vxs), and from a scaled phasor diagram graphically determine the required excitation voltage (Eph) and load angle (8). (c) The load is now increased to 3 MW with the Excitation Voltage kept constant. Using the phasor diagram drawn in part (c) graphically determine the resultant phase current, power factor and load angle. (d)
7. The total rotational losses of an induction motor are a combination of ------- A) Friction losses B) Windage losses. D) Stray losses. C) Core losses. 8. The developed mechanical power can be calculated using the equation of- A) PAG - PRCL. B) PAG w sync C) (1-s) PAG. D) 3 E2Gc. 9. For an induction motor, if the synchronous speed is 1800 r/m, and the rotor speed 180rad/sec, then the slip will be: A) 5.5% C) 6% B) 4.5% D) 4% 10. The power losses in the stator part of the induction motor are B) Core losses D) Friction and windage losses A) Stator copper losses C) Air-gap losses
A three-phase induction motor used for a commercial application in Oman 50HZ runs at 584 rpm at no load and at 546 rpm at full load. a) How many poles do this motor have? b) What is the percentage slip at full load? c) The frequency of the rotor currents when slip is 7 % d) The frequency of the rotor currents at standstill.
Q2. a) A 415V, 50Hz, 3-phase induction motor supplies its rated power to a load. The rated speed of the motor is 980 rpm. b) Two synchronous generators, G2 and G2, are connected parallelly supplying a load. Generator G1 has a no-load frequency of 50.5 Hz and a slope of 300 MW/Hz. Generator G2 has a no-load frequency of 50.2 Hz and a slope of 500 MW/Hz. The load consumes 250 MW real power. (i) At what frequency does this system operate, and how much power is supplied by each of the two generators? (ii) An additional 100 MW load is added to this power system. What is the new system frequency, and how much power do G1 and G2 supply? (iii) The governor set point of G2 is changed to control system frequency back to 50 Hz. Determine the G2 governor set point.
A synchronous machine is a three-phase, two-pole machine with 36 stator slots and 5/6 full-pitched balanced armature windings. Each phase winding is made up of eight identical coils connected in sequence. Balanced three-phase 66 Hz currents with a peak amplitude of 16 A are used to drive the stator phases. a) What is the basic stator space mmf's maximum amplitude? (A.turns) b) How fast does the fundamental stator space mmf rotate mechanically? (rpm) c) What is the third-harmonic stator space mmf's maximum amplitude? (A.turns) d) What is the fifth-harmonic stator space mmf's maximum amplitude? (A.turns) e) How fast does the fifth-harmonic stator space mmf rotate mechanically? (rpm)
The rotor resistance and standstill reactance of a 3-phase induction motor are 0.015 Q and reactance 0.09 0 per phase. (i) What is the p.f. of the motor at start? (ii) What is the p.f. at a slip of 4 per cent? (iii) If the number of poles is 4, the supply frequency is 50-Hz and the standstill e.m.f. per rotor phase is 110 V, find out the full-load torque. Take the full-load slip as 4 per cent.
9