(b) A supply voltage of 240 V was applied to a parallel configuration of an inductive load and a non-inductive resistor. An inductive load takes a current of 3.3 A and a non- inductive resistor takes 3.1 A. Determine the following: (i) The inductive load impedance and non-inductive resistance. (ii) The power absorbed by the inductive load. (iii) The power factor of the inductive load.

(b) A supply voltage of 240 V was applied to a parallel configuration of an inductive load and a non-inductive resistor. An inductive load takes a current of 3.3 A and a non- inductive resistor takes 3.1 A. Determine the following: (i) The inductive load impedance and non-inductive resistance. (ii) The power absorbed by the inductive load. (iii) The power factor of the inductive load.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What is the unit of the product of inductance and capacitance? A. second B. square of second C. 1/second D. 1/second2
A resistance of 20 ohms and an unknown capacitance are connected in parallel to a 110-Vac, variable frequency source. When the frequency is 60 Hz, the current drawn by the circuit is 6 A. At what frequency will the current drawn falls to 5.8 A.
Figure 2 shows three "LC" circuits, two of them with capacitance capacitors "C" and the three with inductance coils "L", the three circuits are coupled by means of two capacitance capacitors "Cc". The currents that circulate through each mesh are those indicated in the figure: "I1", "I2" and "I3". Using Kirchhoff's law for voltages and taking into account the definition of current I = −dQ / dt, find the system of coupled equations of the system and then find the normal angular frequencies of the system.
Figure 2 shows three "LC" circuits, two of them with capacitors of capacitance "C" and the three with inductance coils "L", the three circuits are coupled by means of two capacitors "Cc" capacitors. inductance "L", the three circuits are coupled by means of two capacitors of capacitance "Cc". The currents circulating through each mesh are those indicated in the figure: "I1", "I2" and "I3". Using Kirchhoff's law for voltages and taking into account the definition of current I = -dQ/dt, find the system of coupled equations of the system and then find the angular normal frequencies of the system.
A utility company plans to connect a total of 20uF of capacitance to a 7200 volt line. To make this connection four capacitors will be connected in series. What is the capacitance of each capacitor? Answer is 80uF. Now what is the minimum AC voltage rating of each capacitor?
low voltage systemsWhich of the following is true in pure inductive circuit? a) Current can be 90 forward or backward. b) Current in phase with voltage. c) The current lags behind the voltage by 90. d) Current stays beyond 90 ° to voltage.
A pure resistance of 50 ohms is in series with a pure capacitance of 100 microfarads. The series combination is connected across a 100 volt, 50 hz source. Find the a) impedance, b) phase angle, and c) equation of the current
1. Enumerate five formulas for five series connected inductances across Vt source and draw the circuit. 2. Enumerate five formulas for five parallel connected inductances across Vt source and draw the circuit.
a. individal current b. voltage source
A 25ohm resistor is connected in series with a %0 mH inductor. This circuit is connected to a 120V, 50Hz supply. Solve for a. Inductive reactance b. impedance c. S d. P e. Q
a) Owen’s bridge is one of the AC bridges used for measurement of unknown inductance in terms of known value capacitance. Write balance equation for Owen’s bridge and derive the relations for unknown resistance and unknown inductance
In the circuit in Figure 2, the capacitor andThe circuit of resistance is defined as a load circuit.a) Find the average power dissipated by the load circuit?b) How much of the average power calculated in a) by the resistance in the load circuit and how muchspent by the capacitor? Interpreting the results obtained?c) In the circuit in Figure 2, with a resistance of 80 ohms 23?A coil of is connected in series. In this case,calculating transformer ratio () to optimize power delivery to the load? Obtainedinterpreting the result?d) Calculate the distributed load complex power and reactive power in the newly learned circuit?