b) A cooling machine releases 450 J/°C. How much it looses in kJ per °F

Q: Which among the following is a forming process in which thickness of the metal plate is decreased by…

A: Metal forming processes are the processes in which plastic deformation of the material is done in…

Q: Impact velocity equation

A:

Q: Write short notes on significance of grashoff number.

A: The answer is given below

Q: Differentiate between single acting and double acting cylinders.

A: Differentiate between Single Acting & Double Acting Cylinder :

Q: 30o0mm*300 mmXJ0omm

A: Given data :- 300mm × 300mm × 300mm  Compare L × b × h  Here L= length           b= width…

Q: The column consists of a wooden post and a concrete footing, separated by a steel bearing plate.…

A: Given data: The working stress for wood is σWood=1100 psi The working stress for concrete is…

Q: What is the maximum thickness dimension allowed on the part?

A:

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: 4. To determine the upper and lower surface to beds ,we use. .type from ripple marks *

A: Given :-  To determine the upper and lower surface to beds ,we use ............type from ripple…

Q: Open-die forging (upsetting) involves reduction of height of a specimen between two flat dies using…

A: Forging is the forming process in which metal is shaped by applying force using hammer or…

Q: Customary units by using the values listed for length and mass as defined values: Bending moment or…

A: As moment bending moment or torque has two variables, force and distance. So, M = F × r…… (1) The SI…

Q: 6 m

A:

Q: Round number to three significant figures. 1.548937 x 10^7

A: For scientific notations significant digits/figures are calculated only for the coefficient or…

Q: 5.) A pin made of steel is inserted in a short hanging wooden member and is used to support load F =…

A: Given dataSupport load F = 20kNUltimate strength of the wood is 60Mpa in tension and 75MPa in…

Q: Is 2.0cm3 of aluminum same as 2.0cm3 of lead

A: According to the given data, the volume of the aluminum object is 2.0 cm³  and the volume of the…

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A:

Q: d W Pm a Ps

A: The free body diagram of the system is showing below –

Q: 2 Brass expands more than iron when heated. How would the strip look after prolonged exposure to…

A:

Q: 1- Draw Torque vs. angle of twist for steel specimen

A: INTRODUCTION : Whenever the specimen subjected to the twisting moment that is torque, the stress…

Q: Which one of the following material has the sheet metal applications O a. Mild steel O b. Cast iron…

A: Sheet metal is metal forming process which is used for forming into sheets

Q: 1. Given that the length of the sample is 90 mm and the diameter of it is 7 mm. i. Draw the stress…

A: Write the expression of stress. Write the expression of strain. Draw the given table and calculate…

Q: Why should stress not exceed the material by design?

A: Every component is designed based on working stress which will acts on the component during its…

Q: Qi) Answer only Seren of the following multiple choice: 1- Green sand mold mean mixture of: a- Clay…

A: 1.Green Mould sand is a mixture of sand ,clay and water. Answer: Option c 2.Cores are made of high…

Q: Exalo S. F.d 4o KN/m Braw and B.M.d Ax=o,た Sohato Ay

A:

Q: b) The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32…

A: Find  Mean effective pressure Indicated Power

Q: What is quasistatic compression ?

A: "Quasi-static processes" are ideal reversible processes which cannot occur in practical(real…

Q: Puncher 20 mm o 25 mm thick Punched out F 10 20 mm 25 mm

A:

Q: Explain revision B?

A: As you can see in below image, at highlighted location, in revision B, there is diameter with upper…

Q: Fill in the blanks with appropriate words a) Absorbed energy before breaking:…

A: (a) Absorbed energy before breaking:The absorbed energy before breaking is typically referred to as…

Q: Fine-grained materials have stress-hardening properties. a. True b. False

A: To be explained :-Effect of fine-grained materials on stress hardening properties

Q: Question 4 )Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the…

A: Dear student, we are suppose to solve only one question. Please post other question as a separate…

Q: The below column (diameter 1 in.) is subjected to a compressive force where the diameter is…

A:

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.