(b) A continuous and aligned fiber-reinforced composite is to be produced using 45 vol% of aramid fibers and 55 vol% of polycarbonate matrix. Mechanical properties of these two materials that are given in Table Q5(b): Table Q5(b): Mechanical properties of fiber and matrix Modulus of Elasticity (GPa) Tensile Strength (MPa) Aramid Fiber 131 3600 Polycarbonate 2.4 65 If the stress on the polycarbonate matrix is 35 MPa, when the aramid fibers fail, then compute the followings: (i) the longitudinal tensile strength (ii) the longitudinal modulus of elasticity

(b) A continuous and aligned fiber-reinforced composite is to be produced using 45 vol% of aramid fibers and 55 vol% of polycarbonate matrix. Mechanical properties of these two materials that are given in Table Q5(b): Table Q5(b): Mechanical properties of fiber and matrix Modulus of Elasticity (GPa) Tensile Strength (MPa) Aramid Fiber 131 3600 Polycarbonate 2.4 65 If the stress on the polycarbonate matrix is 35 MPa, when the aramid fibers fail, then compute the followings: (i) the longitudinal tensile strength (ii) the longitudinal modulus of elasticity

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What fiber fraction would be required for a composite with titanium fibers in a polycarbonate matrix (E = 2.5 GPa) to have the fibers handle 85% of a longitudinal tensile load? (Titanium Ef = 116 GPa )
1 Which one below is true for thermoplastic polymers? * O They do not soften when heated and do not harden when cooled. O Most cross-linked polymers are thermoplastics. O None of them. O They are harder and stronger than thermosetting polymers.
Can someone assist me please? Thanks.
A rectangular plate of composite material is formed with unidirectional fibres orientated at 30 degrees to the longitudinal axis. The composite material has properties in the principal material directions of E₁ = 150 GN/m², E₂ = 45 GN/m², V12 = 0.28, V21 = 0.37 and G₁2 = 75 GN/m². A stress of 60 MN/m² is applied to the plate on the longitudinal direction? What is the strain in this direction. Give you answer in micro-strain. Your Answer: Answer
answer quickly
A stress of 1 kPa in a polymer deceased to 0.98 kPa after six weeks. This polymer is to hold a bundle of steel rods for up to one year. If the stress is less than 1.5 kPa, the band will not hold the rods tightly. Determine the initial stress needed to hold the rods.
i need the answer quickly
From the attached image. Annotate and explain the phases of the polymer stress-strain curve.
On the basis of fiber length and orientation, which of the following results to an 'isotropic' properties of fiber-reinforced composites. Continuous and aligned Discontinuous and randomly oriented Discontinuous and aligned
I need help on this
At an axial load of 25 kN, a 50-mm-wide by 20-mm-thick polyimide polymer bar elongates 2.8 mm while the bar width contracts 0.29 mm. The bar is 190 mm long. At the 25-kN load, the stress in the polymer bar is less than its proportional limit. Determine (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar thickness. Answers: (a) E= (b) v= (c) Athickness= i i GPa mm
What is the tensile strength of a composite fibre when its diameter is 20 microns and its critical fibre length is 30 microns? The strength between the fibre and matrix is 150 MPa.