B 12 ft A C 9 ft - 5 ft-

Q: A beam comprises of two metals (1 and 2). Both the metals are in contact as shown in figure. If a…

A:

Q: A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P =…

A:

Q: P5 The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting…

A:

Q: Ҫар 10 3. The force on the chain in the system shown F = 500 N Find the average tensile stress on…

A: It is required to determine the average tensile stress on the chain. σ=FAc Here F is the force, and…

Q: 4m + 6m EA 1 77777 D 4 rigid 5m 3 kN/m Figure-3 7m 4444 2EA B₁ 1 1 1 I The rigid beam AB in Figure 3…

A: To find the stress in bar 1 and 2

Q: Q.1/The bar AD is considered to be absolutely rigid and is horizontal before the load of 200 KN is…

A:

Q: A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. IfP-7…

A:

Q: The rods AB and CD are made of steel having a failure tensile stress of ?FAIL = 500MPa. Using a…

A:

Q: The rods AB and CD are made of steel having a failure tensile stress of ?FAIL = 500MPa. Using a…

A:

Q: Please see the image attached. Thank you

A: Torque = 50kip-in G = 11x106psi

Q: A prismatic shaft consists of a solid brass rod of diameter 32 mm, which is inside a steel tube of…

A:

Q: The compound beam is pin supported at C and supported by a roller at A and B. There is a hinge (pin)…

A: Note:- As per our company policy in case of multiple parts questions, we can solve only first 3…

Q: A rigid bar AB, pinned at end A, is supported by a wire CD and loaded by a force P at end B as shown…

A: Given:  E =210 GPa  Displacement at B not more than 6mm Diameter of wire = 5mm   To Find: Maximum…

Q: SAMPLE PROBLEM 1: USE LRFD The W21 x 93 beam sown in the figure must transmit a total reaction of…

A:

Q: Auniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P-7…

A: Determine the axial deformation of uniform bar 1 in mm

Q: Q.1//The bar AD is considered to be absolutely rigid and is horizontal before the load of 200 KN is…

A: to find stress in each rod

Q: Formül; T Tmaks TL 2 5 için = 2 =(1- 0,630b/a) M2(Izy.z-ly-y) + M,(1,.z – Izy-y) 1.ly - Izy Ox + dy…

A:

Q: The steel member shown below has a diameter of 69 mm, modulus of elasticity of E = 200 GPa, and is…

A: Given Reaction at B 110 kNSpan 5.8 mTo find out Load P

Q: 5) A flanged bolt coupling consists of 8 10mm diameter steel bolts evenly spaced around a bolt…

A: The given data is as follows: Number of steel bolts=8Diameter of steel bolts=10 mmDiameter of steel…

Q: The rods AB and CD are made of steel having a failure tensile stress of ?FAIL = 500MPa. Using a…

A:

Q: The assembly consists of two 20-mm diameter rods AB and CD, a 30-mm diameter rod EF, and a rigid bar…

A:

Q: The aluminum rod AB GPa) iš bondéd tỏ tó the brass rod BD (G = 39 GPa). Knowing that portion CD of…

A:

Q: The assembly consists of two steel bolts AB and EF and an aluminum rod CD. When the temperature is…

A: Free body diagram of rigid cap. Applying equation of equilibrium in vertical direction,Summation of…

Q: -28 The figure below shows a shaft of three segments. It is restrained (fixed support) at both sides…

A:

Q: Determine the coordinates of the mass center of the welded assembly of uniform slender rods made…

A:

Q: Problem 3 The shaft consisting of steel and aluminum segments carries the torque T and 2T. Find the…

A:

Q: The tension AB in the truss as shown in the figure below, is 100 N .Fill the following blanks: 2 m D…

A:

Q: The rods AB and CD are made of steel having a failure tensile stress of ?FAIL = 500MPa. Using a…

A: Given data  Failure tensile stress = 500 MPa  Factor of safety (F.0.S) = 2  Find the smallest…

Q: Consider the girder and the moving loads shown in (Figure 1). Suppose that P = 80 kN. Figure 1 A 6m…

A: Beam:Rolling loads:To find:The maximum live bending moment at C caused by the moving loads.

Q: Determine the magnitude of the pin force at A. Assume W = 640 Ib, a = 3.5 ft, b = 2.6 ft, r = 8 in.…

A: Step 1

Q: The two shafts are made of A-36 steel. Each has a diameter of 21 mm and they are connected using the…

A:

Q: The uniform bars AB and BC are connected with a pin at B and placed on a horizontal surface. The…

A: Sketch the free body diagram.

Q: 10. The assembly consists of a steel rod CB and an aluminum rod BA, each having a diameter of 12 mm.…

A: From figure ; consider part BC ; We know that displacement is given by ; δBC = P1L1A1 E1  P1 = 18 -…

Q: P5 The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting…

A: Given :

Q: O O OO O o o W shape

A:

Q: P5 The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting…

A:

Q: A mild steel bar of length 450 mm tapers uniformly. The diameters at the ends are 36 mm and 18 mm,…

A: Given data : diameter (d1)=36 mmdiameter (d2)=18 mmE=2×105  N/mm2Length (L)=450 mmForce (P)=12 KN

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.