AY-connected three-phase induction motor has the following values printed on the nameplate: 230V line voltage, 60HZ, 6-pole. Additionally, it has the following parameters in ohms/phase as referred to the stator: R1=0.5 Q, R2'=0.250, X1=0.75, X2'= 0.50, Rc=5000, and Xm-1000. The friction and windage loss is %3D 150W. At a rated slip of 2.5%, determine:(a) The input power (b) The stator Cu- loss, (c) The rotor Cu-loss (d) The air-gap power (e) The shaft torque (g) efficiency

AY-connected three-phase induction motor has the following values printed on the nameplate: 230V line voltage, 60HZ, 6-pole. Additionally, it has the following parameters in ohms/phase as referred to the stator: R1=0.5 Q, R2'=0.250, X1=0.75, X2'= 0.50, Rc=5000, and Xm-1000. The friction and windage loss is %3D 150W. At a rated slip of 2.5%, determine:(a) The input power (b) The stator Cu- loss, (c) The rotor Cu-loss (d) The air-gap power (e) The shaft torque (g) efficiency

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 3-phase, 6-pole induction motor con- nected to a 50 Hz supply runs at 975 rpm on full load. Its full-load slip is (a) 25% (c) 2.5% (b) 1.5% (d) 2.0%
None
ICua_RWaUpXC0w/ -------Source and its rotor trom 26 Hz source. The motor will run at الاجابة تكون بكتابة رقم صحيح و يدون وحدات * (2) ihi The efficiency of the 1 phase induction motor could be better increased-4 * by adding a permanently capacitor in series with the starting winding O adding a permanently 2 capacitors in series with the starting winding none of the mentioned all the mentioned O 4 2aio عدم إرسال كلمات المرور دبر نماذج Go ogle مطلقا. A e University of Basrah J
Q4) What is the effect in series motor if you assume V = Eb , with low resistance fielding winding ? a) b) The given information about series motor on full – load (with that the flux is proportional to the field current) is a ) takes ( 78A) and runs at (850 r.p.m) , the series winding resistance is (0.04 2) , with diverter in parallel with the field winding is a (0.18 2) and the armature resistance is (0.09 S2). ( 220 V Neglected the iron, friction and windage losses. Determine the efficiency , speed when developing full load torque ,the maximum efficiency .
A 400 V, 50 Hz 30 hp, three-phase induction motor is drawing 50 A current at 0.8 power factor lagging. The stator and rotor copper losses are 1.5 kW and 900 W respectively. The friction and windage losses are 1050 W and the core losses are 1200 W. The air-gap power of the motor will be
Define the working of the Three phase induction motor with the properly labelled diagrams
A 400V, 25hp, 60HZ, 4 pole, Y-connected induction motor has the following impedances in ohms per phase referred to the stator circuit: R1=0.6410, X1=1.106 Q, Rp=11.080, Xf=6.680 .The total rotational (windage and friction) losses are 1100 W and are assumed to be constant. The core loss is jumped in with the rotational losses. For a rotor slip of 3.2% at the rated voltage and rated frequency, the stator current is
2) A large 3-phase, 4000 Va (phase to phase), 60 Hz squirrel-cage induction motor draws a current of 385 A/phase. The total active power at the stator input terminals is 2344 kW, when operating at full load. The corresponding speed is accurately measured and found to be 709.2 r/min. The stator is connected in wye and the resistance between two stator terminals is 0.10 Q. The total iron losses are 23.4 kW and the windage and friction losses are 12 kW. Calculate the following: c) The total 1²-R losses in the rotor d) The load mechanical power (kW), torque (kN•m), and efficiency. S = Va · V3 - I S= Vy•3·I %3D
Hury up pleaaaaaaase
(Qld) A three-phase 20-pole induction motor is rated at 800 V, 50 Hz. What is the synchronous speed of this machine if the voltage at its terminals is reduced to 400 V (a) 150 rpm, (b) 300 rpm, (c) 600 rpm, (d) 3000 rpm
Q.14. What is slip in an induction motor? Q.15. What is the value of slip at start in an induction motor?
S1) please hury up its late