AW 310 x 118 section with a length of 8.0 m is used as a column Determine the safe axial load the column can carry using AISC specifications with Fy = 345 MPa when: a) column ends are fixed b) one end of the column is fixed; the other free Properties of W 310 x 118

AW 310 x 118 section with a length of 8.0 m is used as a column Determine the safe axial load the column can carry using AISC specifications with Fy = 345 MPa when: a) column ends are fixed b) one end of the column is fixed; the other free Properties of W 310 x 118

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

57 : Design a T-beam having cross section shown in figure below according to ACI code requirement. The beam is simply supported on span 1914 of (7.31m), The is subjected to service dead load (48.80 kN/mm) (including self-weight), and service live load (25 kN.m), Assume the designer intends dnes to use: fe-21 MPa, fy=414 MPa and bf= 1 m. Use two layer of reinforcement) at lan COSM 0.09mm RÝM OC ¹0.3 m² 1000 -0.55 m
Compute the permissible axial load on the column section shown in Fig. 11-8. 4 m, (b) 6 m. modulus of elasticity 2.03 X 10° N/mm2. The effective length of the column is (a) The steel has a yield point of 355 N/mm2 and E180 5.5 F17 51-9 (678-17 180.2 300 284 51. 9 |v 12.5 (c) (9) Fig 11-8 (a)
A W36x210 can be used for Transfer Girder ‘A’ as shown in the elevation next page.Assume the LRFD loads on the ‘Transfer Girder’ are as follows:Pu= 200 kips from the column above. Assume also that the loads from self-weight of thewu = 2.0 kip/ft (girder self weight and beams framing into this transfer girder are equivalentto a uniformly distributed load). These loads are shown in the last figure.a) Check whether the W36x210 ‘Transfer Girder’ is adequate for bending and shear.Assume the unbraced length Lb =20 ft.b) Suppose that service loads, w and P, are both 50% dead load and 50% live load. Does theW36x210 satisfy a service live load deflection limit of L/480?
Homework 1- For a simply supported beam with span 6.0 m , determine the area of steel required to reinforced the beam(350*550) mm if it subjected to service dead load (including to self-weight) (40 kN/m) and service concentrated live load (PL 100 kN) use f'c = 25 MPa & fy 350MPA P= 100 kN Wdl= 40 kN/m 550 mm 350 mm
The compression member shown is made of HE300B section. If Fy is equal to 320 MPa:a) Check the section for local buckling. b) Determine the maximum compressive service load that can be supported if the live load is twice as large as the dead load.
An A36 W14X605 simply supported steel beam with span “L” carries a concentrated service liveload “PLL” at midspan. The beam is laterally supported at supports and its midspan. Consider its beam selfweight to be its service deadload, “w” (use ASEP steel manual for selfweight, w and other section properties). a. Check for compactness of the given section? b. In checking section's compactness, calculate the upper limit for compact flange category? c. In checking section's compactness, calculate the upper limit for non-compact web category?
AW 18 x 97 column is shown below. The column is made up of ASTM A992 steel. It is braced on its weak axis at distances 2m and 4m measured from the bottom support. (a) Determine its critical slenderness ratio. (b) Is the column section compact or slender? Does this column section satisfy the conditions for Section 505.3 of 2015 NSCP Vol. 1 to be used? (c) Determine the design capacity of the column. Use ASD specifications. (d) Considering that LL/DL = 3.0, determine the maximum permissible total service load that should be applied to the column for it not to fail. 000 000 000 0009
A W12x79 section is used as partially restrained column for a floor 8 meters high. The steel used is Grade 60 (Fy = 415 MPa). The W12x79 section has a gross cross-sectional area of 14,968 sq.mm, radius of gyration along strong axis is 133.65 mm, and radius of gyration along weak axis is 77 47 mm. Using k = 0.70, Calculate the design axial strength (KN) of the column by LRFD. The nominal compressive strength, Pn, shall be determined based on the limit state of flexural buckling. Pn= FerAg (505-3-1) The flexural buckling stress, Fr, is determined as follows: 1. when 2. when KL r ≤ 4.71 (or F. ≥ 0.44F,) For = [0.65872|F₂ KL * >4.71 F (or F, <0.44F,) For = 0.877F. (505.3-2) (505.3-3)
AW14 x 43 column in a braced frame has a yield stress of 50 ksi and a height of 10 ft. The column is pinned at the top and bottom and has no intermediate bracing. Determine the available strength of the column considering the critical stress for flexural buckling. From AISC Manual Table 1-1, the properties of a W14 x 43 are: A = 12.6 in^2 tw = 0.305 in bf/2tf = 7.54 h/tw = 37.4 rx = 5.82 in ry = 1.89 in Ix = 428 in4 ly = 45.2 in4 G= 11,200 ksi J = 1.05 in^4 Cw=1950 in^6 What is the nominal axial strength considering flexural buckling stress of the column section (in kips). O 310 O 468 O 447 O 375 O 420 O 436 O 517 O 280
Problem 1.A compression member is 30 feet long. It is made up of ASTM A500 Grade B (Fy= 46 ksi and Fu = 58 ksi) rectangular HSS 12x8x3/16. Assume k-value equals to 1.0 and Q= 1.0 . If the member carries an axial load composed of 26 kips dead load and 77 kips live load, is the member adequate? Use E=29000 ksi. a. Solve for the gross area.b. Compute for the design strength against squash load.c. Solve for the moment of inertia and radius of gyration for both axes. (X-X and Y-Y)d. Compute for the design strength against global buckling.e. Solve for kL/rfor both axes.(X-X and Y-Y)f. Solve for Fcr.g. Solve for design strength against local buckling.Check first if Local Buckling is applicable.h. Compute for the ultimate load to be carried by the member. Use LRFDLoad Combination.i. Does this member have enough strength? Why or why not?
A simply supported beam (L = 14-ft) is laterally braced only at the ends (see diagram). The40-kip load is a service live load. Use Fy = 50 ksi and determine whether a W12x50 is adequate. Useboth LRFD and ASD to check its adequacy. Hints: Check footnotes to verify if compact or not (no needto manually calculate). Use the AISC design-aid tables to determine Lp and Lr (i.e. don’t need tomanually determine these). Look up Cb from a table, no need to manually calculate.
Q.2: Determine LRFD design strength Ø. Pn for the axially loaded column (2C4x4.5) back to back if column length (25 ft) with fixed to fixed end supports and Fy= 50 ksi steel is used. ][[]=