ation of Mass Questions 76-80 are based air entering a compressor operating at steady state with a pressure of 14.7 psi, a temperature of 80 F, and a volumetric flow rate of 1000 cfm. At the exit, the pressure is 100 psi and the temperature is 400 F. Assume the ideal gas model is valid. 76. The air inlet mass flow rate mi can be determined from a. pi[AV] b. [AV]1/v both of the above. C. d. none of the above. 77. The air exit mass flow rate m2 can be determined from a. p:[AV]: b. [AV]z/v2 c. mi d. all of the above.

ation of Mass Questions 76-80 are based air entering a compressor operating at steady state with a pressure of 14.7 psi, a temperature of 80 F, and a volumetric flow rate of 1000 cfm. At the exit, the pressure is 100 psi and the temperature is 400 F. Assume the ideal gas model is valid. 76. The air inlet mass flow rate mi can be determined from a. pi[AV] b. [AV]1/v both of the above. C. d. none of the above. 77. The air exit mass flow rate m2 can be determined from a. p:[AV]: b. [AV]z/v2 c. mi d. all of the above.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The published technical information is shown below for TempStar air conditioners. Rating is provided for an outside air temperature of 95°F and an inside temperature of 80°F. For the model N4A318AKA: a.What is the COP [1.96] b.What is COP Carnot [36.0]
Check Your Understanding 55 55. A polytropic process (n = - 1) starts with P = 0, V = 0 and ends with P 600 kPa, V = 0.01 m3. Find the boundary work done. а. 1 k] b. 2 kJ с. 3 k] d. 4 kJ Check Your Understanding 56 The value of Cp and cy depend on a. Temperature of the gas b. y and R c. Pressure of the gas 56. d. All of the mentioned 54
Engine Cycle: Our inventor is still trying to design a heat engine that will outperform the Carnot cycle .. Design #801-456 is for an ideal, reversible engine that operates with the cycle shown below (A → B → C → D → A). The engine contains 0.421mol of a gas that has a heat capacity ratio of y = 1.300. Point Pressure [N/m²] Volume [m³] Temperature [K] A 1.05 x 105 0.010 300 B 1.85 x 105 0.010 529 1.85 x 105 0.014 751 D 1.05 x 105 0.014 426 PA B A D V (a) What is the efficiency of this engine cycle? (b) What is the efficiency for a Carnot cycle working between the same maximum and minimum temperatures?
1.3 A mixture of two liquids of equal volume is made, the one has a relative density of 0,8 and the other a density of 980 kg/m³. What will the weight of 2 500 litres be? 1.4 1.5 1.6 15 1.7 [21830 N] A solid block of stone with a relative density 4 is broken down and crushed to an average size of 20 mm. If the stone originally had a volume of 50 m³, how many truck loads with a volume of 2 m³, will it take to transport the crushed stone if 25 of the crushed stone has a mass of 80 kg. Has the relative density changed? How much? Why? [32 truck loads] Use table 1.4.2 to determine the kinematic viscosity of crude oil with a density of 855 kg/ m³ at temperatures of 20°C and 100°C. [9,357 x 10-6 m²/s; 3,275 x 10-6 m²/s] Air is used in a sensitive gyroscope to keep the metal bearing surfaces apart. Will the friction losses in the bearing be higher, lower or the same if the temperature of the bearing increases? A widely used S.I. unit for kinematic viscosity is centi- stoke cSt. One stoke is…
Water flow with a density of 998 kg / m3 at 70 ° C enters the system at a speed of 0.5 m / s and a 20 cm diameter pipe is pumped to a 2.5 m high reservoir with the help of a 7.5 kW pump. With the heater at the exit of the system, 1300 kW of energy is transferred to the water flow. Calculate the exit temperature of the water. (With reference to the height Z1, Z2 = 2.5 m is acceptable, ignore kinetic energy changes.) heater Pa pump and turbine P1 Ws reference plane O--
solve the proble regarding otto cycle and fill the unknow
To raise the temperature of 4.29 grams of H2O from -5.0∘C to 20.0∘C, which part of this heating process requires the most energy? Pay attention to your units!
Your assigned value of y is 30 The following fluids specific heats are used. Fluid Comments X (liquid) Y (ideal gas) Z (liquid) Cp 4.2 kJ/(kg °C) 1.01 kJ/(kg °C) 2.03 kJ/(kg °C) does not change phase R = 287 J/(kg K) does not change phase Note: if any of these problems is impossible, state impossible, rather than a numerical answer. 1) A shell-and-tube heat exchanger with two shell passes and four tube T shell, in passes is used to heat (0.5 + y/40) kg/s of liquid Z from 10°C to 50°C. using 1.5 kg/s of liquid X entering at Trube,in (80 + y/2)°C. The over-all heat transfer coefficient is U = (150 – y) Figure 1: For use in Problem 5 W/(m² °C). a. Find the exit temperature of Fluid X: Tx,out = °C (± 1°C) b. Find the required heat transfer surface area: A = m² (± 1%)
An ideal gas flows through a horizontal tube at steady state. No heat is added, and no shaft work is done. The cross-sectional area of the tube changes with length and this causes the velocity to change. (a) Derive an equation relating the temperature to the velocity of the gas.(b) If nitrogen at 150 [°C] flows past one section of the tube at the velocity of 2.5 [m/s], what is the temperature at another section where its velocity is 50 [m/s]? Let Cp = 7/2R.
Need help with engineering problem. Match the RTT term with its explanation: A: ddt(∫CVβρdᏉ) B: ∫CSβρVcosθdAout C: ∫CSβρVcosθdAin A. B. C. Match one of the following answers below to each letter. A change within the control volume Outflow of B from the ontrol volume Inflow of B to the control volume
Thermodynamics 2
C4