At what velocity does air and water flow convert from laminar to transitional in a 5 cm diameter pipe at 20°C? At temperature 20°C, Air 1.164 18.240 x 106 Water Density (kg m³) Viscosity (Pa-s) 998.2 993.414 x 106

At what velocity does air and water flow convert from laminar to transitional in a 5 cm diameter pipe at 20°C? At temperature 20°C, Air 1.164 18.240 x 106 Water Density (kg m³) Viscosity (Pa-s) 998.2 993.414 x 106

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The recorded velocity of the upper limit of the critical region is 32 ft/s. Determine the diameter…

Q: AIR P= 7 KPä. 1.5 m OIL HINGE SG = 0.82 A GATE 2450 3m The gate shown in the figure is hinged at A…

Q: For a fully-developed flow of water in a pipe having a diameter 10 cm, velocity 0.2 m/s, and kinetic…

A: Given data- A fully developed flow of water in a pipe- Diameter d=10 cm, Velocity V=0.2 m/s,…

Q: While the pressure remains constant at 85 psig, the volume of air changes from 20 ft3 to 12 ft3.…

A: Give data: P= 85psiV1 (initial volume) = 20 ft3V2 (final volume) = 8 ft3∆V=V1-V2=20-12=8…

Q: A pipe 40 cm in diameter contains steam at 100°C and is covered with asbestos (K = 0.0006…

Q: The pipe diameter is 75 mm, roughness of pipe is 0.15 mm length is 300 m, water velocity in the pipe…

Q: The recorded velocity of the upper limit of the critical region is 32 ft/s. Determine the diameter…

Q: What is the pressure difference between the air pipe and the water pipe ? WATER, SH0 = 9800 N/m3…

A: Please refer the attached image for complete solution. THANK YOU !

Q: Q7. If a soap bubble has to sustain an absolute pressure of 101.35 kPa with its diameter being 25 mm…

Q: 6. What pressure of air in the headspace at location A is needed in order for the glycerin to rise…

A: The pressure is defined as the force per unit area. - Unit weight of the fluid H - Heigth of the…

Q: Questions #1 Water flows at the rate of 0.16 L/s through a 200 mm diameter pipe. If its Viscosity…

Q: Taking the coefficient of compressibility of water to be 2200 MPa, determine the pressure increase…

Q: An old pipe of diameter 2.5” is carrying water at a velocity of 4 ft/s. Determine the Reynolds…

A: Given data in question Diameter of pipe Length of pipe Velocity of flow Kinematic viscosity To…

Q: 1. In undisturbed air stream, where the pressure is 14.7 psi and density is 101325Pa, where the…

Q: An old pipe of diameter 2.5” is carrying water at a velocity of 4 ft/s. Determine the Reynolds…

A: Given: Diameter of pipe, D = 2.5 in Velocity of flow, v = 4 ft/s Length of pipe, L = 200 ft…

Q: An incompressible air is flowing at a velocity of 60 mph through a duct 4 sq. ft. in cross-section.…

A: Given:- Velocity in duct (V) = 60 mph or 88 ft/s Area of duct = 4 ft2 Pressure difference (∆P) = 8…

Q: Energy losses in pipe: L = 1.3m, D= 14 mm, ε/D = 0.007 Type of Reynold's Calculated Calculated pipe…

Q: 18. Air with a density of p = 1.2 kg/m³ flows in an inclined ventilation duct having a cross-…

Q: Inviscid flow Frictionless flow = No viscous resistance %D %3!

A: The inviscid flow-The flow of an inviscid fluid in which the viscosity of the fluid is equal to zero…

Q: Water is flowing at a rate of 8 ft³/s in a rectangular channel with a 2 ft water depth and a 4 ft…

Q: Determine the amount of air added to the tank (in Ibi

A: Amount of air added is 9.8lbm

Q: Exercise 2: According to an appliance manufacturer, the 4-in,-diameter vent on a clothes dryer is…

Q: Oil with viscosity of 0.10 Pa-s and s+ 0.85, flows through 3,000 m of 30 cm cast-iron pipe at rate…

Q: Question Water flows through a 100 mm diameter pipe with a velocity of 0.015 m/sec. If the kinematic…

A: Water flow in a pipe-Pipe diameter d=100 mm,Velocity V=0.015 m/s,kinematic viscosity To Find-The…

Q: Find the moment of inertia about the x' axis of the channel cross-section if the channel material…

A: Given:Required:Moment of inertia about x' axis

Q: The highest velocity (in cm/sec) for flow of water of viscosity 0.01 poise to be laminar in a 6 mm…

A: Laminar pipe flow- Viscosity=0.01 poise Pipe diameter=6 mm Highest velocity of flow of water=?

Q: The highest velocity (in cm/sec) for flow of water of viscosity 0.01 poise to be laminar in a 6 mm…

Q: Q2. Air having a specific weight of 0.0795 lb/ft³ flows into the duct at A with an average velocity…

Q: 2. A compressible air inside an instrument tube is flowing at 350 m/s at standard sea level. The…

A: For compressible fluid continuity equation is given by the following formula, ρ1A1V1=ρ2A2V2 Here…

Q: A 20 mm diameter pipe has a length of 80 m. Water with a viscosity of 0.04 Pa-sec is flowing thru…

Q: 5.The change from laminar to turbulent flow depends upon the velocity and viscosity true O False

A: Laminar flow is defined as the movement of liquids without turbulences. The fluid flows in parallel…

Q: ing at the flow rate, an

A: given data, Q = 500 m3/s Diameter, d = 1 m length, L = 75 m dynamic viscosity of air = 1.825 * 10-5…

Q: The flow in a pressurized pipe is laminar. Kinematic viscosity coefficient of the fluid is 106m2/s,…

A: Kinematic viscosity = ν = 10-6 m2s Pipe diameter = d = .5m Cross sectional velocity = Vc = .0032ms

Q: Compute the resulting pressure in kPa after a "real" diffuser in which the energy loss due to sudden…

Q: 5. A line was determined to be 3798. 25m when measured with a 50m steel tape supported thorughout…

Q: See the sketch below from our textbook. The positive x-direction is to the right. The bottom wall is…

A: Given data in question Area 5 m2 Velocity profile 8y-0.3y2 Viscosity 0.482 N sec/m Depth 4 mm To…

Q: let V be a fluid flow velocity vector.is the flow irritational? incompressible?why?V= [-z,2x,y]

Q: A 2.5 mm diameter glass tube inserted in a reservoir filled with water is shown below. At 20 degrees…

Concept explainers

Pressure and Stress

Question

At what velocity does air and water flow convert from laminar to transitional in a 5 cm
diameter pipe at 20°C?
At temperature 20°C,
Air
1.164
18.240 x 106
Water
Density (kg m³)
Viscosity (Pa-s)
998.2
993.414 x 106

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Water at 50°F flows at a rate of 4 ft/s in the space between 6-in Schedule 40 steel pipe and a square duct with inside dimensions of 10 in. The shape of the duct is Figure below. Compute the Reynolds number to determine if the flow is laminar or turbulent. 10 in. 6 in. diainler
Can you please help with the below Qs?
pipe 310 m Water is flowing in a straight concrete lining centrifugally spun pipe as shown in the figure problem 12. The difference between the two gauge readings is 185 kPa. The flow rate is designed to be 30 liter/s. By using Darcy Weisbach and Hazen William's formula, determine the pipe diameter. (Ans.: 228 mm, 123 mm) TABLE 5.1: Pipe Characteristies Pipe Hazen-William* Roughness e (mm) 0.15 C 140 Asbestos Cement (AC) – all ages Cast Iron, Ductile Iron - new 0.3 130 10 years old - 20 years old 1.5 3.0 100 90 Cast Iron coated – good condition all ages Welded steel - uncoated - new 0.3 135 125 100 100 - old 0.6 1.5 Coal tar enamel coated steel – new Concrete lining centrifugal spun – all ages Galvanized Iron (GI), Mild Steel (MS) HDPE, UPVC, Polyethylene Wrought Iron Copper, Brass *The Malaysian Water Association - MWA (Design Guidelines for Water Supply Systems) 0.15 0.15 140 0.3 130 0.015 155 0.045 ND 0.0015 ND ND = No Data
Describe Permeability (Hydraulic Conductivity).
Water at 60 degrees Fahrenheit have a density of 62.36 Ib/ft.^3 and dynamic viscosity of 7.536 x 10^-4 Ib/ft-s) is flowing steadily in a 2-inch diameter horizontal pipe made of stainless steel at a rate of 0.2 ft^3/s. Use f = 0.0200. Determine %3D the head loss in terms of inches over a 200-feet long section of the pipe. A) 327.60 В 27.30 C 376.05 D None of the above
In an annular section built with commercial steel pipe, the outer diameter is said to be 13 inches and inside a commercial steel pipe the inner diameter is found to be 23 inches which carries a water flowrate of 500L/sec. The total length of the section is 8m. Calculate the frictional loss in meters of water at a temperature of 60F
(Avoid truncation in the middle of solution thank you) The atmospheric pressure in a certain location was obtained to be 100 kPa Determine the gage pressure in kPa 2.0m below the surface of a body of liquid(specific gravity 1.50) in nearby lake 29.43 192.34 129. 93 92.43
Estimation
Q.15 Water is flowing through two pipes one of 10 mm diameter and second of 5 mm diameter and both are discharging in 12 mm diameter pipe. The rate of flow in 10 mm diameter is 1.0 c.c./s. If the Reynolds number of 12 mm diameter pipe flow is 4000, determine the rate of flow in 5 mm diameter pipe. Consider kinematic viscosity equal to 6.5 x 10-7 m²/s.
An 80 kph stream of water from a nozzle. How high could the water jet rise without taking into account air resistance?
Water is flowing at a rate of 3ft/s through a pipe of diameter 1.5in and length 120ft. Determine the Reynolds number and the friction factor of the pipe. Take the value of kinematic viscosity of water as 1.052x10-5 ft2/s.
MY REGISTRATION NO IS 5350