At what speed (in meters per second) must the sliding rod in the figure below move to produce an emf of 1.00 V in a 1.65 T field directed perpendicular to the rods and into the page, given the rod's length is 29.0 cm? ΔΑ = (ΔΧ X m/s x Ⓡ RⓇ Application of Lenz's R law X RHR-2 O O B₂X B O O increasing 3R Equivalent circuit RHR-1

At what speed (in meters per second) must the sliding rod in the figure below move to produce an emf of 1.00 V in a 1.65 T field directed perpendicular to the rods and into the page, given the rod's length is 29.0 cm? ΔΑ = (ΔΧ X m/s x Ⓡ RⓇ Application of Lenz's R law X RHR-2 O O B₂X B O O increasing 3R Equivalent circuit RHR-1

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A 140 V emf is across a transformer's 190-turn primary coil. How many turns should the secondary have in order to produce a 40 V emf, expressed as an integer. Can you set up Es/Ep = Ns/Np. I know I am to solve for Ns. I need to see what is given tied to the symbols, then I see what to what better.
A mass spectrometer is being used to separate common oxygen-16 from the much rarer oxygen-18, taken from a sample of old glacial ice. (The relative abundance of these oxygen isotopes is related to climatic temperature at the time the ice was deposited.) The ratio of the masses of these two isotopes is 16 to 18, the mass of oxygen-16 is 2.66-10-26 m S they are singly charged and travel at 5.106 in a 1.25 T magnetic field. What is the separation Ad=2r₂-2r₁ between their paths when they hit a target after traversing a semicircle? Ion source F=qE FE Ad= F = qvB FB Things to Prepare: 1. Make a list of information given to you. + m Bout V 12r₁ 212 m₂ 2. Identify the formula for the radius of the trajectory for particles in the magnetic field. 3. Set - up the formulae in step 2 for the two for the particles. 4. How can you manipulate the formulae in step 3 to solve for the answer? Bout kg, and
The switch in figure has been open for a long time. It is closed at t = 0 s. What is the current through the R₁ resistor? (a) Immediately after the switch is closed? (b) After the switch has been closed a long time? (c) Immediately after the switch is reopened? R₁ = 20.0 ; R₂ = 30.0 2; L = 12 mH; & = 40 V R₂ E ww R₁ elle L
The rod shown below moves to the right on essentially zero-resistance rails at a speed of v = 2.9 m/s. 5.0 N 4.0 cm If B = 0.61 T everywhere in the region, what is the current (in mA) through the 5.0 O resistor? Does the current circulate clockwise or counterclockwise? o clockwise o counterclockwise
In the figure, ɛ = 78.1 V, Rị = 14.4 N, R2 2.91 H. Immediately after switch S is closed, what are (a) i and (b) iz? (Let currents in the indicated directions have positive values and currents in the opposite directions have negative values.) A long time later, what = 16.7 N, R3 = 39.3 N, and L = %3D
The circuit given is a square 20 cm on a side. The magnetic field increases steadily from 0 T to 0.50 T in 10 ms. What is the current in the resistor during this time?
At what speed must the sliding rod in the figure below move to produce an emf of 1.10 V in a 1.77 T field, given the rod’s length is 31.0 cm?
The figure represents a moving rod of length 3 cm in a magnetic field B= 4T What is the current in the circuit represented in the figure, if the speed of the rod is 12 m/s and the resistance of the wire is 9 ohms? X X x x x R X X X X x X X X X X X X O I =122.45 mA O I =160.00 mA O I = 11.00 mA O I = 44.90 mA O I = 81.34 mA
QUESTION 1 https://per.physics.illinois.edu/per/IE/ie.pl?phys112/ie/08/IE_movingcoil X X X X XX X W X X X X XX X X X X X X X X X X X X X X X Lg At t=0, a rectangular coil of resistance R = 2 ohms and dimensions w = 3 cm and L = 8 cm enters a region of constant magnetic field B = 1.6 T directed into the screen as shown. The length of the region containing the magnetic field is LB = 15 cm. The coil is observed to move at constant vėlocity v = 5 cm/s. What is the force required at time t = 0.8 sec to maintain this velocity? Answer in uN (u = micro = EE-06)
1.8 Cast-steel Cross-sectional pap1 = 0.5 mm. area -3 cm? 1.6 l4 = 10 cm Silicon iron Cast iron 1.4 Mild steel 1.2 Cross-sectional area 32 ст? 1.0 0.8 Cast iron Cross-sectional area-1.4 cm? = 0.1 mm 0.6 (a) 0.4 0.2A 1000 2000 3000 4000 5000 6000 7000 Magnetic field strength, H(A/m) (b) Figure (1) Silicon Iron uɔ S7 = "1 Flux density, B(T)
At what speed must the sliding rod as shown move to produce an emf of 1.00 V in a 1.50 T field, given the rod’s length is 30.0 cm?
The magnetic field through a single loop of wire 14.0 cm in radius and of 11.5 Ω resistance changes with time as shown in the figure. Calculate the emf in the loop as a function of time. a)What is the emf at t = 1.0 s? For the sign take the loop in the plane of the paper, and the magnetic field out of the paper. Take clockwise to be positive emf. b)What is the emf at t = 3.0 s? c)What is the emf at t = 5.0 s? d)What is the current at t = 1.0 s?