Please help me solve this as soon as possible, and I will surely leave you a like. At the end of the power stroke in an Otto cycle (i.e., bottom dead center), the conditionsin the cylinder are T=966.6 K and P-386.6 kPa. The work produced by the adiabatic,reversible power stroke is 946.2 kJ/kg. Using air standard assumptions, find thecompression ratio of the engine.

Answered: Image /qna-images/answer/8a8d64b8-89f0-4f47-82f3-8bedcc00b1be.jpg

Answered: At the end of the power stroke in an…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Good work on the promblem but the process is a bit hard to read, can you express this in a different way?
Suppose that a company that works in extruding aluminium products has spent L.E. 50,000 on maintenance materials, L.E. 10,000 on maintenance labour, L.E. 250,000 on manufacturing; in order to produce 10,000 tons of extruded aluminium sections. If the total man-hours worked is 1,000 man-hour, the total cost of investment in the plant and equipment is L.E. 5E06, and the preventive and breakdown maintenance costs are L.E. 40,000 and L.E. 20,000, respectively, find the following: a) The ratio of maintenance labour cost to material cost. b) The ratio of total maintenance cost to total output. c) The ratio of total maintenance cost to total manufacturing cost. d) The ratio of total maintenance cost to total man-hours worked. e) The ratio of total maintenance cost to value of facility. f) The ratio of total preventive maintenance cost to total breakdown cost.
We have a rectangular piece. We wish to manufacture a parallel slot along thepiece in a vertical milling machine and 50 cm from the edge. The width of the slot is 40 mm. TheDepth of the slot is 25 mm. For this, several rough cutting steps and aFine cut with a depth of 0.20 mm. The depth for each of the steps ofrough cut is limited to 1.75 mmAditional information:What is the number of blades used for the rough cutting steps?What is the number of blades used for the fine cutting step?
I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the example shows on problem number 1. Here is the link to the questions I already had answered, could you please rewrite the answer so its properly answered as the example shows (Problem 1)? https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857
what process is this? how to perform this? Procedure in position?
Selasi wants a shaft of 5/8 inches diameter to be used in his design project of which he is considering a design factor of 3. He hopes to get the same shaft size or 11/16 inch diameter shaft in the market for his design. So he decided to send his apprentice, Amuzu to the market. Unfortunately, when Amuzu went to the market, there were 1⁄2 inch, 9/16 inch, 3⁄4 inch, and 7/8 inch sizes available in the first shop. Amuzu decided to buy the nearest shaft size in the first shop instead of checking in the other shops where he could have gotten either 5/8 inch or 11/16 inch sizes.a. Discuss the consequences Selasi would incur in his design project if Amuzu had bought 9/16 inch size shaft. b. Discuss the consequences Selasi would incur in his design project if Amuzu had bought 3⁄4 inch size shaft.
2) A washer is going to be manufactured by cutting operation out of 2024ST aluminum alloy sheet that has a thickness of 2.5 mm. The outside diameter of the washer is 25.0 mm, and the inside diameter is 12.0 mm. Make a rough sketch, define the geometries to be used and determine a. The punch and die size for the blanking operation b. The punch and die size for the punching operation c. The force required performing the blanking and punching operation simultaneously. The aluminum has a tensile strength = 300 MPa.
What are the three most common grips for drawing? Explain each type of grip, along with their advantages and shortcomings in different drawings. Provide some examples.
In winter season, he chemical observed a snow from a pavement that is being scooped up to a height of 40 ft by an endless bucket-scoop. and is then dropped into a container. He noticed that, at the highest point, the snow moves at 3 k’s. A total of 66 hp is needed to scoop snow at the rate of 100 lb’’s. Assuming a loss of 10% due to friction, calculate the percentage of tool work need to melt and break up the snow.
Provide and illustration to what is asked.
I was given this image for the purpose of studying for an upcoming exam. No additional info was given. Any suggestions on how to study for potential questions that could be asked about this image?
Help

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

At the end of the power stroke in an Otto cycle (i.e., bottom dead center), the conditions in the cylinder are T=966.6 K and P-386.6 kPa. The work produced by the adiabatic, reversible power stroke is 946.2 kJ/kg. Using air standard assumptions, find the compression ratio of the engine.