At STA. 51+33 of a proposed road, the center height of the cross- sectional area is 1.4m in fill while the center height of the cross- sectional area at STA 51+93 2.8m in cut. The width of the proposed road is 14m with a required side slope of 2H:1V for both cut and fill. Determine the volume of cut and the volume for fill using the END-AREA Method. (All sections are level sections)

At STA. 51+33 of a proposed road, the center height of the cross- sectional area is 1.4m in fill while the center height of the cross- sectional area at STA 51+93 2.8m in cut. The width of the proposed road is 14m with a required side slope of 2H:1V for both cut and fill. Determine the volume of cut and the volume for fill using the END-AREA Method. (All sections are level sections)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Build the following part. Report the volume in mm^3. Assume all dimensions are in mm.

A: Volume of 1=(40×17×38) - Volume of 2 =(40×17×38) - 12×10×10×17…

Q: Two cylindrical rods, one of steel and the other bronze are joined at C and restrained by rigid…

Q: Please copy paste ans other wise down vote

Q: Compute the maximum flexural stress if the maximum internal bending moment of the beam is 60 KN-m.…

A: Maximum moment (Mmax) = 40 KNm = 60 × 106 N•mm To find:the maximum flexural stress.

Q: For the cross-section area is shown below, the centroid (in mm) measured from the base is equal to:…

A: To find CG divide I section in three parts as bottom flange as first part ,web as second part and…

Q: The cantilever beam geometry shown is made from steel E=200GPA. Determine the deflection and the…

A: To calculate the value of slope and deflection at point B, using the double integration method. In…

Q: The material has a specific weight y = 85 lb/ft². (Eigure 1) Figure 0.25 ft 0.5 ft Zift 1 ft 1 of 1…

A: = 85 lb/ft3

Q: For the objects shown on the left below, circle the letters corresponding to all possible…

A: To select the correct answers among the given options as per the given condition in the question.

Q: area of the triangle s

A: A triangle is a 3 sided geometric figure . Area of the triangle with three different sides is given…

Q: The cantilever beam geometry shown is made from steel E=200GP.. Determine the deflection and the…

A: Due to loading on the beam acting at any point or entire beam makes the beam deflect and that…

Q: The force of F = 50 lb acts along the edge DB of the tetrahedron shown in (Figure 1). Figure ▾ Part…

Q: Please solve the following problem so I can understand with step by step solutions

A: To find the centroid of the given figure, follow the steps below: Step 1: In a 2-D coordinate…

Q: The 1-section has the dimensions (in mm) shown in the figure. Calculate the second moment of area…

Q: Which of the following is the fastest speed? E Click the icon to view the conversion table. Choose…

Q: Reading sequence 1 2 3 4 5 6 7 8 9 10 11 12 13 Reading the ruler 1.35 1.72 1.98 2.05 2.17 2.76 2.98…

Q: What is the total area of the two triangle shapes (a) and (b) (in square inches)? 182.25 X Your…

A: Given, To find side 1, 2 ,3 and 4 Total area of two triangle shape (a) and (b) Area of rectangle…

Concept explainers

Alloys

An alloy is an admixture of two or more metals or a metal and a non-metal. Since ancient times, man has been using alloys. Alloying helps to retain the properties of the parent matter, such as hardness, strength, toughness, ductility and is corrosion-resistant. Copper alloys such as brass have antimicrobial properties that help to fight against (Coronavirus disease 2019) COVID-19 and other hospital-acquired infections. Some common alloys are brass, bronze, solder steel, etc. Most alloys have a lower melting point than their constituents. This is due to the presence of a nonmetal as one of the constituents that behaves as an impurity and restricts the raise of melting point.

Question

Draw the figure to illustrate your understanding of

all the problems.
Show complete formulas and solutions.
Round off to 3 decimal places. Enclose all final
answers in a box.

At STA. 51+33 of a proposed road, the center height of the cross-
sectional area is 1.4m in fill while the center height of the cross-
sectional area at STA 51+93 2.8m in cut. The width of the proposed
road is 14m with a required side slope of 2H:1V for both cut and
fill. Determine the volume of cut and the volume for fill using the
END-AREA Method. (All sections are level sections)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

I was absent from this weeks lecture. They want us to chart the answer in excel or word and I can’t figure out how to do this.
Question: 7. Replace The Loading System By An Equivalent Resultant Force And Specify Where The Resultant's Line Of Action Intersects The Member Measured From A. A 200 Lb 50 Lb -3 Ft — 3 Ft 3 Ft 30° 100 Lb
Please solve full SOLUTIONs. One page don't do it in steps thanks
A triangle inscribed in a semi-cirice with radius r shown below. Locate the centroid from point O. Also determine the Moment of Inertia with respect to its Horizontal Neutral Axis (x bar - axis)
Pls i need answer asap. Show complete solution and figures with unknowns. Fluid Mechanics: A slab of wood 0.80 m x 0.80 m by 0.25 m thick, S = 0.50, floats in water ( specific weight of water=9800 N/m^3 ) with a 840.84 N load on it. Determine the volume of slab submerged in cubic centimeter. Write your answer in whole number.
pls answer the table also
Please answer all parts ! This is one question ! Write clearly ! Thank You! The specific gravity of a material is 5.4 What are its specific weight in US units? Answer: 5400 Ibf/ft^3 A material has a density of 13406.32 kg/m3. What are its specific weight? Answer: Choose...
Given the below diagram, calculate the height h, showing all your work for full marks. 110 m 35° hị 68°
From the figure below, locate the centroid from x and y axes as shown.
pls help! Write the complete solutions and legibly. Answer in 2 decimal places. UPVOTE WILL BE GIVEN! MECHANICS OF DEFORMABLE BODIES Let Q = 0 and T = 6 (Example: 4QT mm2 = 406 mm2). Just substitute the number in letter. Thank you! A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the figure. The cross-sectional area of each bar is 4QT mm2. Determine the average axial stress in each bar.
A block of wood 0.25 m thick is floating in sea water. The Specific Gravity (SGw) of Wood is 0.35 while that of sea water (SGs) is 1.02. Summarize your answer like the format below and Find the minimum AREA of a block that will support a man weighing 80 kg. (Clue: - m^2) 大, Wman = 80 kg Wwooo BF Weight of the man Unit weight of the wood N m Unit weight of sea water Equation of Volume of Wood Block N m Area of the block m? zlzzE