At an axial load of 24 kN, a 35-mm-wide by 15- mm-thick polyimide polymer bar elongates 3.0 mm while the bar width contracts 0.15 mm. The bar is 230 mm long. At the 24-kN load, the stress in the polymer bar is less than its proportional limit. Determine (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar thickness.

At an axial load of 24 kN, a 35-mm-wide by 15- mm-thick polyimide polymer bar elongates 3.0 mm while the bar width contracts 0.15 mm. The bar is 230 mm long. At the 24-kN load, the stress in the polymer bar is less than its proportional limit. Determine (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar thickness.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At an axial load of 25 kN, a 50-mm-wide by 20-mm-thick polyimide polymer bar elongates 2.8 mm while the bar width contracts 0.29 mm. The bar is 190 mm long. At the 25-kN load, the stress in the polymer bar is less than its proportional limit. Determine (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar thickness. Answers: (a) E= (b) v= (c) Athickness= i i GPa mm
A bar ABCD consists of three sections: AB is 25 mm square and 50 mm long, BC is of 20 mm diameter and 40 mm long and CD is of 12 mm diameter and 50 mm long. Determine the stress set up in each section of the bar when it is subjected to an axial tensile load of 20 kN. What will be the total extension of the bar under this load? For the bar material, E = 210 GN/m 2. [32, 63.7, 176.8 MN/m z, 0.062 mm.] can you please answerthis question fully and if you use * can you please tell me what you mea by it?
A steel rod with a cross-sectional area of 150 mm² is stretched between two fixed points. The tensile load at 20°C is 5577 N. What will be thestress at 25°C?
A tensile load of 1700 N is applied to a cylindrical specimen of a metallic 1) alloy. The initial diameter of the specimen is 12.0 mm and the elastic reduction of the diameter due to the load is 7.1 x 104 mm. If the Poisson's ratio of the allow is 0.37, determine the elastic modulus of the alloy.
The stress-strain curve of a thermoset material is given in the figure below. Calculate the total strain energy at the point of fracture for a cylinder (diameter = 3mm and length = 4mm) made from this thermoset material.
The cable of hoist has a cross sectional of 80mm2.The hoist is used to lift a crate weighining 500 kg.The free length of of the cable is 30 m.Assume all deformation is elastic. (a) what is the stress on the cable. (b) How much will the cable extend if it is made from steel(E-200 Gpa)? (c) How much will the cable extend if it is made from polypropylene(E-1.2 Gpa)?
A sample of silicone breast implant, polydimethylsiloxane (PDMS), is placed under unconfined compression. The magnitudes of the resulting longitudinal and transverse strains have been measured to be 2.7 and 1.341, respectively. The young's modulus of the implant is 500 kPa. Calculate the shear and bulk moduli.
At the proportional limit, a 16 mm thick x 69 mm wide bar elongates 6.2 mm under an axial load of 485 kN. The bar is 1.5 m long. If Poisson's ratio is 0.32 for the material, determine the modulus of elasticity (in GPa). Note: Do not include units in your answer. Answer:
L b F What is the change in length (L) of the titanium bar (E = 16.5E6 psi) given: L = 36 in., b = 3 in., h = 0.25 in, and F = 3 kips Answer to above question is 8.72E-3 in, the shear modulus for the bar is 6.145E6 psi, poisons ratio is 0.343. My question is what is the strain (in macrostrain) in the bar in a direction perpendicular to the direction of the applied force? (Answer is 82.8, I need to understand how to reach this answer.)
Question 1: [Strain Energy Due to Direct Stresses] A steel bar of a length, diameter and Young's modulus of 400 mm, 20 mm and 200 GPa is placed concentrically within a brass tube which has an outside diameter, thickness, length and Young's modulus of 30 mm, 4 mm, 400 mm long and 100 GPa respectively. The compound bar hangs vertically with its upper end rigidly fixed with a collar fitted to the bottom end. The application of a load P re sults in the compound bar storing a total of 7J of energy. Calculate: 1.1 The gradually applied load 1.2. The suddenly applied load
Please answer in proper units
Diameter 14 mm, length 100 mm aluminum wire sample, axial When a load of 80 kg is applied in the tensile direction, the change in length and Calculate the change in diameter.(Ealuminum=70 Gpa)