At a proposed hydroelectric power plant site, the tailwater elevation is 490m. The estimated energy to be produced is 52,650,000 kW-hr per year. Expected flow of water is 1665 cubic meter/min. The turbine manufacturer set the ff. performance data: turbine efficiency is 87%, Generator efficiency is 92%, and the loss of head will not exceed 3.8% of the available head. Determine: a.) the water power in kW b) the available head in meters c.) The head water elevation in meters

Q: A two-stroke, 12-cylinder diesel engine with an effective power of 2440 kW at 550 rpm manufactures.…

A:

Q: A hydro electric generating station is supplied from a reservoir ,at a head of 100 meters. If the…

A: Given       Head, H = 100 m      Electrical Energy, E = 500 MWh      Efficiency = 75% = 0.75…

Q: A mining pit about 5000ft below sea level was flooding as a result of heavy down pour. The situation…

A:

Q: The difference between the headwater and the tail water elevation is 150 m. The head utilized by the…

A: Dear student,                     According to the expert guidelines, I am allowed to answer only…

Q: How many minimum turbines are required to produce 10000 kW power if: - The KE of the wind is…

A:

Q: Steam enters a turbine at 600 ᵒC at 7300kPa pressure and leaves the turbine as saturated steam at 75…

A: a) Given values in the question inlet pressure P1=7300kpa Exit pressure P2= 75kpa specific volume at…

Q: in a steam power cycle, steam enters the turbine at 20 bar with the following different conditions…

A:

Q: Steam flows steadily through an adiabatic turbine. The inlet conditions of the steams are 4 MPa, 500…

A:

Q: Figure shows a hydraulic elevator which capable to carry 450 kg of passengers from the ground to the…

A: Since we only answer up to 3 subparts so we will answer the first 3. Please resubmit the question by…

Q: Steam enters a turbine at a mass flow rate of 1.4 kg/s, a pressure of 700 kPa and a temperature of…

A: Given that , m=1.4 kg/s˙P1=700kPaT1=400°CP2=100kPav2=1.4 m3/kgQout=50kW

Q: Problem 2. At a hydroelectric power plant the flow is 3.25 meter cubed per second, the friction loss…

A: Given, Inlet flow = Qin = 3.25 m3/sFricition head loss in penstock = Hf = 15 mAvailable head  = H =…

Q: Q1:A pump is to increase the pressure of 200 L /s of water by 4 MPa. The water enters through a…

A:

Q: B) A hydraulic system contains a pump that discharges oil at 13.8 MPa and 0.00632 m/ s³ to a…

A:

Q: Question B2 A fountain fires a jet of water from a 5 mm diameter pipe at ground level vertically…

A:

Q: urbine accepts water at 15 MPa, 600 C and enthalpy of 3581 kJ/kg. After expansion stage, the…

A:

Q: Steam at 8600 kPa and 500 degree Celsius passes through a turbine and expands to 10 kPa. If the…

A: The enthalpy of the steam at the inlet can be determined as, The specific entropy of the steam at…

Q: Argon is heated at 350 K with a mass flow of 4 kg/s as it passes through a pipe. Given that the heat…

A:

Q: A nozzle receives 36 kg/s of air at a speed of 142 m/s and with an enthalpy of 1060.00 kJ/kg. Air…

A: The exit velocity from the nozzle is (a) V = 824.72 m/s. (b) V = 842.71 m/s.

Q: A Thermal power plant rated capacity of 12,530 MW operates 11 hrs per day. If the actual energy…

A: Given Power of plant = 12530 MW Time = 11 hrs  Actual energy generated = 42% higher of rated To find…

Q: Turbine accepts water at 1.2 MPa, 250 C and enthalpy of 2934 kJ/kg. After expansion stage, the…

A:

Q: 2)A)What is convection in Heat Transfer ? B)Does the convection affect the lifetime of the turbine?…

A: 2(A) Convection is a heat transfer phenomenon in that bulk movement of molecules within fluids. The…

Q: If the blade length is 59.9 m, wind speed 15.4 m/s and air density is 1.23 kg/m³, then the wind…

A:

Q: Using the specific rotation speed, what would be the best turbine option for a waterfall of 120m and…

A:

Q: A 400 MW power plant consumes coal containing 1.167x1011 BTUS of thermal energy every day. Energy…

A: Given Data Consumed energy inlet is: Energy generated is: The energy in joule is Energy outlet is

Q: A geothermal power plant was installed at the rear side cliff of Mayon Terrain that generates…

A:

Q: Water vapor enters an adiabatic turbine at a pressure of 8 MPa, a temperature of 600 ℃ and a speed…

A: Given data:Inlet conditions:Inlet pressure (P1​) = 8 MPaInlet temperature (T1​) = 600°CInlet speed…

Q: HW2: A hydroelectric power plant built for a design head of Hn=12.5 m should develop a rated output…

A: Given: Head of the plant→Hn=12.5 m Rated power→P=12000 hp=8952 KW Because efficiency→e=0.90 Density…

Q: spectively, which of the following is the energy obtained

A: Option(A) is correct

Q: 1- For the total heating load equal to 25 kW, and using hot water temperature difference of 10'C for…

A: Given: The heating load, Q = 25 kW The temperature difference, dT = 10oC The length of pipe, L = 100…

Q: Tsource P₁ =W₁ 2 11. Control volume: Turbine To process m, P2, T2, V₂

A: Turbine  The turbine is among the most often utilized pieces of technical equipment today. They are…

Q: 2. A constant load (-120 MW) supplied by a hydro and a steam unit. Find the generation schedule for…

A: Given: Here are the given data, Constant load, P=120×106 w V=3×106 m3 Time, t=7 days 168 hours To…

Q: In a steam turbine, saturated steam enters the turbine at a pressure of 16 MPa and a pressure in the…

A:

Q: 4. Consider a river flowing toward a lake at an average speed of 3 m/s at a rate of 500 m3/s at a…

A: Given:Average speed of water, v=3 m/sVolume floe rate of water, Q=500 m3/shead available, h=55 m

Q: The rate of flow of water through a horizontal pipe is 271 lit/s. The area of the pipe suddenly…

A: We need to calculate head loss, pressure in larger pipe and power lost

Q: 2 .A two-stroke four-cylinder ideal Otto engine operates at 4800 rpm. Air is taken in at 101 kPa and…

A: Given data A  two-stroke  four-cylinder  ideal  Otto  engine  operates  at a speed =  4800  rpm Air…

Q: A) A hydropower station has a head of 9 meter and three 10 MW units are installed to extract energy…

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: 12. An electric generating station is designed to have an electric output power of 1.40 MW using a…

A: The above question is based on the application of conversion of energy.

Q: 3) Consider a Pelton Turbine system. Two jets, they are exactly the same, strike the bucets of it.…

A:

Q: A) Calcule el trabajo neto por ciclo, en kJ; B) la potencia desarrollada por un motor, en kW y C) La…

A:

Q: The difference between the headwater and the tail water elevation is 150 m. The head utilized by the…

A:

Q: Q1) An inward flow reaction turbine is working under a head of 25 m and running at 300 r.p.m. The…

A:

Q: with an enthalpy of 600 Kj and velocity of 250 m/s, a 4kg of air enters a turbine. The enthalpy at…

A: Given DataThe initial enthalpy is; The initial velocity is; The mass of air is; The final enthalpy…

Q: In the Ericsson cycle, the pressure of the air entering the compressor is 100 kPa, its temperature…

A:

Q: 1)A)What is Conduction in Heat Transfer ? B)Does the Conduction affect the lifetime of the turbine?…

A: 1(A) Conduction: Conduction is a way of transferring the heat from one solid object to another solid…

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.