data:Ea = +800µ,Ep = +960µ,Ec = +800Determineb) maximum shear strain (Ymax)Gage cGage bGage a

Answered: Image /qna-images/answer/3ef881df-0537-4c9a-8899-2f8618811388.jpg

At a point on the free surface of an aluminum alloy (E = 10) x 10" psi and v = 1/3) machine component, the three strain gages shown in Figure below were used to obtain the following strain data: Ea = +800, Ep = +960µ, Ec = +800u Determine a) the three principal strains (E1, E2, amd E3) b) maximum shear strain (Ymax) Gage c Gage b Gage a

At a point on the free surface of an aluminum alloy (E = 10) x 10" psi and v = 1/3) machine component, the three strain gages shown in Figure below were used to obtain the following strain data: Ea = +800, Ep = +960µ, Ec = +800u Determine a) the three principal strains (E1, E2, amd E3) b) maximum shear strain (Ymax) Gage c Gage b Gage a

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 50 x 10 3 mm while those at CD decrease 80 x 103 mm in the 250- mm-gage length. Using E = 170 GPa, determine the flexural stress at the top %3D fiber. Answer must be in MPa. Given: a = 50 mm, b = 110 mm, and c = 80 mm. %3D gage length A a mm B b mm D с mm
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 30 x 10-3 mm while those at CD decrease 60 x 103 mm in the 220- mm-gage length. Using E = 130 GPa, determine the flexural stress at the bottom fiber. Answer must be in MPa. Given: a = 50 mm, b = 130 mm, and c = 70 mm. %3D gage length a mm A b mm c mm B.
In a plain strain condition in XY plane, normal strain in X and Y directions are equal to zero and shear strain is equal to 3 x 10-6. What is the diameter of Mohr's circle of strain for these strain values?
9. A titanium T-bar having cross-sectional dimensions shown in Fig.9 is 320mm long and cantilevered out from a fixed wall support. The free end is loaded laterally (downwards) with a force of 5kN. The titanium has a Young's Modulus of 110 GPa. (a) Determine the maximum axial stress (ignoring stress concentrations) (b) Sketch the worst case stress and strain profiles through the depth of the beam and state the highest strain and where it is located. 50 mm 10 mm 50 mm 10 mm Fig. 9 19 Introduction to Stress Analysis [Ans: (a) -192 MPa (N/mm²), -1745 pɛ (bottom of web) ]
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 30 x 10-3 mm while those at CD decrease 60 x 10-3 mm in the 290-mm-gage length. Using E = 150 GPa, determine the flexural stress at the top fiber. Answer must be in MPa. Given: a = 50 mm, b = 120 mm, and c = 90 mm. gage length A a mm b mml c mm
If the lateral compressive strain in a material is 0.3 x 10-3 and the Poisson ratio is 0.25, then longitudinal strain in the material is ✓ 0.0012 (tensile) 0.0012 (compressive) 7.5 x 10-5 (compressive) 7.5 x 10-5 (tensile)
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 40 x 10 -3 mm while those at CD decrease 70 x 10 -3 mm in the 220-mm-gage length. Using E = 180 GPa, determine the flexural stress at the bottom fiber. Answer must be in MPa. Given: a = 40 mm, b = 130 mm, and c = 80 mm.
Question 3 The strain rosette shown below was used to obtain normal strain data at a point on the free surface of a machine part. Under load, the following strains were measured: Ea = -360 µE, Eb = −230 µɛ, &c = 815 µƐ and v= 0.15 a) Determine the strain components Ex, Ey and Yxy at the point. b) Determine the principal strains and the maximum in-plane shear strain at the point. Figure 1 b 120° 120° 120° a I
At a point in a machine component that is subjected to plane stress, the normal and shear stresses are 0 = 100MPa, oy = 35 MPa, and Txy = 70MPa, acting in the directions shown in the figure. Oy Txy Ox
Find the req,
At a point in a machine component that is subjected to plane stress, the normal and shear stresses are σx=σx= 100 MPa, σy=σy= 20 MPa, and τxy=τx⁢y= 28 MPa, acting in the directions shown in the figure. At this point, determine the strain components εxεx, εyεy, εzεz, and γxyγx⁢y. Assume that E = 68 GPa and v = 0.32 for the machine component.
In the marine crane link CD is has a uniform cross section of 50 x 150 mm and a modulus of 200 GPa. Determine the axial stress and change in length of link CD. Reference: Beer, et.al., 7th Edition Mechanics of Materials 35 m 15 m C D -15 m A -25 m. B 3 m 80 Mg