At a point in plane stress the principal stresses were found to be 22 MPa(T) and 14 MPa (C). The maximum shear stress at the point is

Q: can you do it in polygon

A: Given vectors : A :  2 kph 45°N of E B :  2.8  kph 58°E of S C :  5.1  kph 28°W of S D : 3.2  kph…

Q: Consider two infinite parallel plates in length, where the top plate is moving to the right at a…

A:

Q: 355 coupe for some maintenance check. Before proceeding to your regular maintenance routine, it is…

A: Odd matric number:

Q: Based on the system shown in Figure 1, develop the position equations from your fixed datum lines,…

A:

Q: Write short notes on significance of grashoff number.

A: The answer is given below

Q: Given the isometric drawing, draw the multiview projection. The multiview projection of the glass…

A: Draw the isometric view.

Q: Figure shows a heat exchanger designed to cool 5250 kg/h of an ethyl alcohol solution (Cp = 3810…

A:

Q: S (-36mm) is correct but total distance traveled (166.04 mm) was marked wrong can you help me?

A:

Q: The correct choice is what

A:

Q: Please look at pic. Please help, I don't get part b. Thanks

A:

Q: TC Sin2 * cos' z 2. sin? dx

A:

Q: 5m %3D d=9·8\ mls? १त्र वह w Given data

A: Given data : The value of mass=m The value of acceleration due to gravity=g The value of height=h…

Q: a) What is the reading (degrees, minutes)? b) What is the reading (degree and fractions of a…

A: Reading on main scale = 90 degreeReading of vernier matching with main scale = 22Least count of…

Q: can you do the SF and BM calculation with explanations

A:

Q: What is the center of gravity in this figure?

A: given; center of gravity on given figure?

Q: Finding the y centriod.

A: Given data, the I section is given with dimensionFind outthe centroid along the y-axis

Q: I o2s+lo4 s+1. .96 2. L'st ++T?

A:

Q: 3. both wires is identical at 1.5 meters and both wires are 5 mm in diameter. The steel wire is made…

A:

Q: 97SD Make freehand sketches of any four (in all) common tools, utensils or pieces of furniture . 1.

A: Table is a furniture. Thus, sketch table:

Q: Name the following figures.

A: Pneumatic Cylinder Pivot Bracket with rigid bearing AB7

Q: Another name for "SIZE DESCRIPTION is: 37 A Dimensioning B Orthographic projection. C Assembly…

A: Given Engineering drawing To find Size description Leader line Extension line

Q: IF y = u² + 3u² & u = 2x Find dy dx

A:

Q: Q34 gine exCumphe far nolineer operautor an

A: Given: To give an example of non-linear operator.

Q: 02 2N Find markdore.

A: Given data : The value of force applied F=2 N The value of Distance moved by an ball d=1.1   To find…

Q: 1. average velocity is correct (-0.75 m/s) but instantaneous velocity (-1 m/s) is incorrect can you…

A: Given :    To find : instantaneous velocity v when t =4 s

Q: 28 cm a? 100 cm 30° V 15 cm

A:

Q: This statement is true or false? Process of making raw material to a final desired product is called…

A: Given Data : Raw Material Final desired product

Q: The headless type of set screw are known as screws * ....... grub O machine O rag О Сар The only…

A: Isometric drawing is the three-dimensional drawing of the object. It has two types - 1. Isometric…

Q: H.W praw load dingram alesfanding to the given-Shar dingram? 2nd (urve 10 2nd Garve sfin -10 Im Im

A: BMD(Bending moment diagram) is a diagram representing the variation of bending moment along the…

Q: From the projected views obtain the isometric drawing.

A: According to the details provided in the question, there are three views of the first angle of…

Q: la) Compare the relative load strength of the following two bolts: Bolt 1 = %" Dia x 3" Long and is…

A:

Q: re did you get 1 for m from???

A: Given data as per questionInitially air containsFirst Phase1P1=30 lbf/in2T1=540°FV1=4 ft3Second…

Q: Why cos(60 if I don't see that angle in the figure

A: This question can be solved by labelling angles.

Q: Fload/8 Fload/4 ffort = Fload/8

A: According to the details provided in the question, we need to calculate  we need to find all forces…

Q: Find this range. Ds i mm

A:

Q: Draw the sectional view of the solid and provide necessary dimensions. E 7 Scale 1:2 Draw the…

A: According to the given datatwo object views are givenWe need to draw the section view of the problem

Q: Lab Activity 5H Calculating Radius End Points on a Lathe Part Use the illustration provided to…

A:

Q: Give 1 example of methods of section

A:

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.