At a point in an elastic material under strain, there are normal stresses of 60 N/mm2 and 40 N/mm2 (both tensile) at right angles to each other, with positive shearing stress of 20 N/mm2. The maximum shear stress and direction its plane will be respectively

At a point in an elastic material under strain, there are normal stresses of 60 N/mm2 and 40 N/mm2 (both tensile) at right angles to each other, with positive shearing stress of 20 N/mm2. The maximum shear stress and direction its plane will be respectively

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A C L/2- Fig. P9.28 to B 24 -L/2-

A: Problem 9.28:Using double intergration method:For the limit;

Q: 3 MPa. Which of the following describes the stress state? A body is subjected to the following…

A: in question stress in various plane is given: question is asking about stress state: given: SIGMAxx…

Q: A steel plate is bent into a circular arc of radius 10 m. If the plate section be 120 mm wide and 20…

A: Given a steel plate bent into a circular arc with, E=2×105 Nmm2. Arc radius, R = 10 m. Area, A=120…

Q: 19.The total deformation may be regarded as possessing the following a.change in length experienced…

Q: Draw the shear force and bending moment diagrams for the beam.

A: Hi! Thank you for the question As per the honor code, We’ll answer one question since the exact one…

Q: At a point in an elastic material, ,40 Nimm a direct tensile stress of 80 N/mm and a direct…

Q: a. Determine the elastic section modulus, Sx. b. Determine the plastic section modulus, Zx. c.…

A: Area, width of flange, depth of section, thickness of flange, NOTE According to company guidelines,…

Q: At a point in a stressed material, the major principal stress is 50 kPa compression and the minor…

A: It is required to determine the maximum shear stress.

Q: itude of maximum shear stress in the

A: This question has been taken from Solid mechanics

Q: Point A in a beam is deformed such that the strain components are ɛx = -1380 µɛ, ɛy = -880 µɛ, Ez =…

Q: At a point in elastic medium normal stresses in two mutually perpendicular directions are 120 MPa,…

A: Normal stresses : = 120 MPa = 40 MPaTangential stress = 30 MPaTo Find :Principal stresses ?

Q: At a point in a strained material, tensile stress of 100 MPa and compressive stress of 60 MPa are…

A: Introduction : The given question is related with solid mechanics . In this question we are provided…

Q: Find normal, tangential and resultant stresses across a plane through the point at 480 to the major…

A: Principle stresses δX=100N/mm2 and δY=40N/mm2 θ=48∘

Q: Question 4 At a point in a material there are two direct stresses of 60 MPa tensile and 50 MPa…

A: Two direct stresses 60 MPa tensile and 50 MPa compressive acting at right angles to each other. The…

Q: The stresses on two perpendicular planes through a point in a body are 160 MPa and 100 MPa, both…

Q: Q- Principal stress at a point in an elastic material are 1.5 o (tensile), o (tensile) and 0.5o…

A: Given- Principal stress- σ1=+1.5σ σ2=+σ σ3=-0.5σ Elastic limit E=210 MPa, Poisson's ratio- μ=0.3,…

Q: A homogenous isotropic material of size 20 cm x 20 cm x 20 cm is placed inside a rigid box of…

A: Consider the free body diagram;Given;Young modulus, E=Poisson ratio, v=0.3

Q: At a point in a machine component that is subjected to plane stress, the normal and shear stresses…

Q: The stresses on two perpendicular planes through a point in a body are 160 MPa and 100 MPa, both…

Q: At a point in a machine component that is subjected to plane stress, the normal and shear stresses…

Q: Element in plane.stress the stresses are and g, = 97 MPa, g, = 76 MPa and T= 22 MPa. Determine the…

A: Radius of the circleR=(σx-σy2)2+τxy2R=(97-762)2+222R=24.38 MPA

Q: Consider a metal single crystal oriented such that the normal to the slip plane and the slip…

A: Note* According to the guidelines given by Bartley since you have asked multiple questions, we will…

Q: For the state of stresses (in MPa) shown in the figure below, the maximum shear stress (in MPa) is 2…

Q: 0.2 In a material there is a horizontal tensile stress of 200 MPa, a vertical tensile stress of 50…

Q: On the cross-section of a steel beam under bending, which one of the following statements is…

A: The maximum normal stress always occurs on the planes of zero shearing stress. The maximum and…

Q: A prismatic bar has a cross-section of 25 mm by 50 mm and a length of 2000 mm. Under an axial load…

A: Width B=25 mm Depth D=50 mm Length L=2000 mm Load P=100 kN Elongation ∆L=2 mm Tensile stress & %…

Q: Question 4 At a point in a thin steel plate in plane stress (0z = Txz= Tyz= 0), Ex=600, &y= - 2004µ…

A: E=2G1+ν=276.921+0.3=200Gpa

Q: The state of stress at a point is given by: o= 80 MPa, oy=100 MPa and tauxv =60 MPa. If the yield…

A: State of stresses-σx=80 MPaσy=100 MPaτxy=60 MPayield strength-fy=150 MPa

Q: Q.1 At a point in a material there is a horizontal tensile stress of 150 MPa, a vertical compresaive…

Q: The limit of proportionality in the material of a structural steel member, when subjected to simple…

A: Given data- Tension stress-σy=280 N/mm2σ1=122 N/mm2 (tensile)σ2=60 N/mm2 (compressive)poisson's…

Q: A mild steel bar is subjected to an axial force P, resulting in an axial stress ♂=100N/mm² What…

Q: AExplain in a few words the difference between the normal stress, the shearing stress, and the…

A: What is stress: It is the internal resistance developed by the body to external load applied to it…

Q: A homogenous isotropic material of size 20 cm x 20 cm x 20 cm is placed inside a rigid box of…

Q: The stresses on two perpendicular planes through a point in a body are 160 MPa and 100 MPa, both…

Q: For the state of stresses (in MPa) shown in the figure below, the maximum shear stress (in MPa) is 4…

A: Given- the state of stresses in the figure. σx=4 MPa,σy=-2 MPa,τxy=4 MPa.

Q: The limit of proportionality in the material of a structural steel member, when subjected to simple…

Q: At a point in a machine component that is subjected to plane stress, the normal and shear stresses…

Q: alculate the principal strain.

Q: (c). At a point in an elastic material the stresses on three mutually perpendicular planes are as…

A: Stresses on three mutually perpendicular planes;

Q: H WW For The Stress state shown, find The principle stresses and Their directions 30Mpa 50 mpa

Q: At a point in a strained material, tensile stress of 100 MPa and compressive stress of 60 MPa are…

Q: Find the value of maximum shear stress Maximum principal stress=8.7 MPa Minimum principal stress=3.2…

A: Given data : The value of maximum principal stress σ1=8.7 MPa The value of minimum principal stress…

Concept explainers

Material Properties

Construction in civil engineering demands high strength, durability, and longevity. These targets can be achieved by better design and analysis, along with the correct choice of materials. Different materials have different properties and hence, they respond and performs differently under the various condition of external loadings. It is therefore a critical task of an engineer to select the right material based on the property that the material is supposed to function in real-time. When speaking about the property, there are different categories of material properties like chemical property, physical property, mechanical property, electrical property, magnetic property, thermal property, etc. These material properties form the basis of material selection in various applications.

Question

At a point in an elastic material under strain, there are normal stresses of 60 N/mm2 and 40 N/mm2 (both tensile) at right angles to
each other, with positive shearing stress of 20 N/mm2. The maximum shear stress and direction its plane will be respectively

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find the req,
At a point in a machine component that is subjected to plane stress, the normal and shear stresses are σx=σx= 100 MPa, σy=σy= 20 MPa, and τxy=τx⁢y= 28 MPa, acting in the directions shown in the figure. At this point, determine the strain components εxεx, εyεy, εzεz, and γxyγx⁢y. Assume that E = 68 GPa and v = 0.32 for the machine component.
Question: Principal stresses at a point are 80 N/mm2 and 40 N/mm² both tensile. The yield stress in simple tension for this material is 200 N/mm2 The values of factors of safety according to maximum principal stress theory and maximum shear stress theory, respectively, are
For the state of stresses (in MPa) shown in the figure below, the maximum shear stress (in MPa) is 2- 44 4 4 4 2 1
The stresses on two perpendicular planes through a point in a body are 160 MPa and 100 MPa, both compressive, along with a shear stress of 80 MPa. What is the normal stress on a plane inclined at 30° to the plane of 160 MPa stress? (a) -42.4 MPa (b) -75.7 MPa (c) -59.1 MPa (d) -86.3 MPa
Theory of failure.
At a point in a machine component that is subjected to plane stress, the normal and shear stresses are σx=σx= 60 MPa, σy=σy= 80 MPa, and τxy=τx⁢y= 42 MPa, acting in the directions shown in the figure. At this point, determine the strain components εxεx, εyεy, εzεz, and γxyγx⁢y. Assume that E = 72 GPa and v = 0.29 for the machine component.
A point in beam experiences a tensile stress (due to bending) of 50 N/mm2 and a shear stress of 20 N/mm2. The principal stresses are:
If €, and e y are the maximum and minimum strains, respectively in the neighbourhood of a point in a stressed material, then what is the expression for the maximum principal stress?
I need the answer quickly
Question- Principal stress at a point in an elastic material are 1.50 (tensile), o (tensile) and 0.50 (compressive). The elastic limit in tension is 210 MPa and poisson's ratio=0.3. Find the value of o at the failure when computed by the maximum principal strain theory.
Solve only 4.4 and 4.5