at 60° C flows through the very wide duct. Suppose that = 210 mm v = 18.9(106) m²/s. (Eigure 1) ure 0.5 m/s < 1 of 1 > 0.5 m/s Part A Determine the required dimension a of the duct at x = 4 m so that the central core flow velocity maintains the constant free-stream velocity of 0.5 m/s. Express your answer to three significant figures and include the appropriate units. O a= Value Submit Request Answer Provide Feedback Units ?

at 60° C flows through the very wide duct. Suppose that = 210 mm v = 18.9(106) m²/s. (Eigure 1) ure 0.5 m/s < 1 of 1 > 0.5 m/s Part A Determine the required dimension a of the duct at x = 4 m so that the central core flow velocity maintains the constant free-stream velocity of 0.5 m/s. Express your answer to three significant figures and include the appropriate units. O a= Value Submit Request Answer Provide Feedback Units ?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Include proper explanation this is fluid mech problem
Question 4. The flowrate of the flow is 0,20 m/s in a pipe placed on a horizontal plane. The pipe diameters are as 0.41 m and 0.28 m for Di and D2, respectively. Find the resultant force *(kN) acting to the pipe by the flow. The gauge pressure at (1) is P1 =280 kN/m2. (y= (1) 10KN/m³) Figure 4
The flow is opened to the atmosphere at point D which is fed by a very wide reservoir that has a water surface elevation of (5+) meters as shown in the figure given below. Elevation of the horizontal axis BC is 1 meter. At sections AB the diameter of the pipe is (0.2+- meters and CD the diameter of the 100 pipe is (0.3+: meters. The flow is ideal (inviscid) and absolute atmosphere pressure is 9.81 N/cm?. Considering the pipe's diameter is (0.15+; m at section BC, find the discharges and the 100 а. velocities of the flow at other sections (AE, EB, BC, CF, FD). Draw the energy and hydraulic grade lines of the system. b. Assuming the system discharge is constant and has the value you have found in (a), calculate the minimum pipe diameter that the section BC can take and draw the energy and hydraulic grade lines of this situation. Note: Absolute vapor pressure of water is 2.26 kN/m?. 10 A E 2.5 D B m
1. A pipe has a slope of 1 in 100 and its length is 300 meters. Its diameter is 0.6 meter at the lower end while 1.2 meters at the higher end. The rate of flow through pipe is 5400 liters/min. Find the pressure at the lower end if the pressure at higher end is 68.07 kPa. Neglect losses.
Question 2: A pipeline carries a pumped flow of 0.05 m/s. The line contains three 90 degree bends (K=0.9), a gate valve (K=0.4), and a swing check valve (K=0.6). Select an internal diameter between 10 cm to 90 cm for steel pipe (e= 0.00015 in, 0.00381 mm). Determine the total head loss if the lengt of the straight pipe is 300 m.
Question In fully developed laminar flow in a circular pipe, if the velocity at midway between the wall surface and the centerline is measured to be 6 m/s, then the velocity at the centre of pipe is
The flowrate of the flow is 0.20 + a/10 m3 /s in a pipe placed on a horizontal plane. The pipe diameters are D1= 0.30 m and D2= 0.20. Please find the force acting to the pipe by the flow. The gauge pressure at (1) is p1 =200 + b*10 kN/m2 . (g=9,81 m/s2, g=10kN/m3 ) a= 4 b=3
Air at 30°C flows through a 70 m long, 2 cm x 2 cm rectangular cross section pipe as shown in Figure 1(b). The flow is laminar flow and centerline velocity is 2 m/s. If the angle of pipe measure from horizontal plane is 35º, determine : (iv) wall shear stress; (v) shear stress at 1 cm from the center of the pipe; and (vi) power required to maintain this flow.
Q.2 For h 1 m in the setup shown in figure find: 1. Pressure head at point a 2. Seepage velocity 3. Find h if the force on screen b is 2.5 kN/m² WIT 1.0m -0.25m Screen b h W.T 41 n=1/3! @ K=0.5 cm/sec. Datum 84=21kN/m³ Cross-Sectional area of the tube=0.5m² -