A two-story office building shown in the photo has interior columns that are spaced 22 ft apart in two perpendicular directions. If the (flat) roof loading is 20 lb/ft2, determine the reduced live load supported by a typical interior column located at ground level. AT22 ft22 ft22 ft –22 ft -Fig. 1–9

The spacing is 22 ft. The flat roof loading is 20 lb/ft2.

Answered: AT 22 ft 22 ft 22 ft – 22 ft - Fig. 1–9

Engineering

Civil Engineering

AT 22 ft 22 ft 22 ft – 22 ft - Fig. 1–9

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Shown below is a floor plan of the library, office and balcony at the second floor level of a condo…

Q: Determine the required strength for LRFD.

Q: ctural steel column between the foundation and first floor which supports the beams above. • Analyse…

A: Given:- characteristic loads pinned bases To find:- Analyze the column indicated in the figure…

Q: what is the moment at point O

Q: (NOS 1-7) A tied column 600 mm x 600 mm x 4.50 m. carries an unfactored dead load of 2080 KN and an…

Q: Question 6 A monolithic floor system consists of 100 mm thick slabs supported by beams 250 mm wide,…

A: Thickness of slab, Width of beam, Span, Dead load, Live load, To find: The bending moment at face of…

Q: The wall is 19 ft high and consists of 2 x 4 in. studs, plastered on one side. On the other side…

Q: Problem- For design of a roof truss, if the design wind velocity is 20 m/s, what is the design wind…

A: Given- Design wind velocity V=20 m/s, Design wind pressure=?

Q: 2.15 Compare the following three roof structures. All three have the same span length and the same…

Q: A column is made of steel and concrete, if the normal forces on steel and concrete are 6.8kip and…

Q: Given is the 200mm X 400 mm rectangular beam below. 9 kN 7.50 kN/m 400 mm 1.50 kNm 7.50m 200 mm…

A: A loaded beam and it’s cross section is given and it has been asked to determine flexural bending…

Q: Civil Engineering For the structure shown below find a) Maximum deflection, b) Critical Buckling…

A: Given:- A beam is given with a point load and a horizontal force The magnitude of the point load =…

Q: Determine the governing (ASD) axial load (kN) for a column in a multistory office building using the…

Q: The floor beam shown in Figure below is used to support the 6-ft width of light weight plain…

Q: The floor of a classroom is to be supported by the bar joists shown in Fig. 2–15a. Each joist is 15…

A: Solution:-The given values are as follows,Each joint =15ftSpaced=2.5ftThe lightweight concrete=4in…

Q: Floor joists 68.2 mm wide by 152 mm high, simply supported on a 4.1 m span, carry a floor loaded at…

A: Given information, B = 68.2 mm H = 152 mm L = 4.1 m w = 4.7 kPa

Q: Determine the LRFD factored load for the following situations on a steel column (Ignore any roving…

A: Factored load : A service load multiplied by a load factor yields factored design loads. Service…

Q: A roof design supports a dead load of 50 lb/ft² and a snow load of 30 lb/ft² In addition, a wind…

A: D = Dead load = 50 lb/ft2S = Snow load = 30 lb/ft2W = Wind pressure = 15 lb/ft² (-ve for…

Q: r joists 64.8 mm wide by 106 mm high, simply supported on a 4.3 m span, carry a floor loaded at 5.1…

Q: Q.2 Find out the load on interior column and exterior column of 1st storey and 3rd floor of a nine…

A: Odd Storeys:1. Calculate Total Dead Load on Odd Storeys:Dead Load=Dead load of odd floor=3,200…

Q: For a one story concrete structural system with height =4 m, if: spans along x= 6 m, spans along y=5…

A: To calculate mid-span reinforcement area of beam : To calculate mid-span reinforcement we have to…

Q: 10 - f 17 in 4-10k D,-0.5 k/ft (excluding weight) 40.75 k/ft (service loads) 10. 4 of 8

A: Given:- f'c = 4000 psi fy = 60000 psi Width of beam=12 in Effective depth of beam=17 in Area of…

Q: Tasks required: (a) Loading analysis (b) Timber properties and parameters for design (c) Bending…

Q: In addition to the design snow load computed in practice problem 3, the roof of the building in…

Q: Determine the fire endurance rating of the beam selected to carry the imposed loads. Extreme fiber…

Q: A 4-storey with Roof deck AFP armory is to be constructed in Sulu. The facility is essential for the…

A: Given - A 4-storey with Roof deck AFP armory is to be constructed in Sulu. The facility is…

Q: Determine the force in each member due to dead load, and rain loads.

Q: A fully-enclosed warehouse is used as a storage facility for flour and other baking products in a…

Q: 6. A reinforced concrete column has cross sectional dimensions of 400mm x 400mm. The column is…

A: To design the reinforced concrete column according to the ACI (American Concrete Institute) code, we…

Q: 4. Floor joists 95 mm wide by 114 mm high, simply supported on a 4 m span, carry a floor loaded at…

Q: A live load reduction of 55% is possible for 5 story building? True or False

A: The maximum possible reduction for different floors is given below,

Q: Calculate the dead and live loads (separately) applied on column D at the first floor Note:…

A: Calculate the dead and live loads (separately) applied on column D at the first floor Note:…

Q: A 25 story building has it columns spaced at 32 ft between centers in each direction. The floor dead…

A: Given that: Spacing of columns = 32 ftDead load = 150 psfLive load = 100 psf

Q: utary areas of the ff: What are the Influence area of the ff: What are the unfactored and factored…

A: Factored Load = 1.2*DL + 1.3*LL = 1.2*2+1.3*4.8 =…

Q: Solution

A: The highest absolute value is 105 lb/ft², which corresponds to the Dead load + Snow load…

Q: A reinforced concrete column 250 mm in diameter is designed to carry an axial compressive load of…

Q: I will rate thx.

A: In order to calculate the transition height for wind pressure on the windward wall of the…

Q: A three-storey bldg has interior columns spaced at 4 m apart in two perpendicular directions. Loads:…

Q: A post-tensioned bonded concrete beam has a prestress of 1560 kN in the steel immediately after…

A: It is given that :

Q: The T- beam used in a heavy storage warehouse is made of concrete having a specific weight of 125…

A: The given figure is shown below:

Q: with 15-20 mm diameter of steel rods. The post is 30 cm in diameter. The limiting stress of the…

A: According to given data A post consists of concrete with 15-20 mm diameter of steel rods. The post…

Q: A three-story hotel (that is two framed floors and a roof, no basement) has interior columns thatare…

Question

A two-story office building shown in the photo has interior columns that are spaced 22 ft apart in two perpendicular directions. If the (flat) roof loading is 20 lb/ft², determine the reduced live load supported by a typical interior column located at ground level.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please make it right and clear,I will vote it up.
3. Floor joists 62.5 mm wide by 196 mm high, simply supported on a 6.1 m span, carry a floor loaded at 4.9 kPa. Compute the center-line spacing between joists in meters to develop a bending stress of 11 MPа.
A 4-storey with Roof deck AFP armory is to be constructed in Sulu. The facility is essential for the housing of the Philippine Army's newly purchased weapons, ammunitions and explosives. The location of the facility is 7.5 km from the known source which is capable of producing a magnitude 6.7 earthquake. The structure is a Steel MRF with an overall height of 14m from the NGL. The weight per level of the slabs and stairs is equal to 1740 kN. For the walls at the typical levels, the weight is computed as 2362.5 kN and for the parapet at the roof deck level, the weight is computed as 388.8 kN. An equipment 2.0 meters high with a hexagonal cross - sectional area whose sides equal to 1 meter is installed at the second level and has a weight of 100 kPa. Using R = 8.5, which of the following most nearly gives the lateral force at the 4th level in kN? Use Soil Type A.
Please answer correctly
Solution?
A column in the upper story of a building is subjected to a compressive load from thefollowing sources: dead load = 15.8 kips, live load = 13.7 kips, roof live load = 18.7 kips,snow load = 16.5 kips, rain load = 17.2 kips, wind load = 13.5 kips, and earthquake load= 11.8 kips. Using ASD, what is the required nominal strength of the column for a safety factor Ωof 1.67?
Q.2 If the (010×10) cylinder compressive strength of O.P.C. concrete at 10-day is (14 MPa). Calculate (20×20×20) cube comp. strength at age of 28 days.
A concrete building has 12 stories, each story is 3.2 m high. The facade column has 400 kN axial load per floor and a cross sectional area of 300mm×700mm. Calculate the shortening of the column at the ground floor level and the sixth floor when using concrete f'c= 25 N/mm and 40 N/mm?. Explain if there will be any effect on the facade.
Please correct solution
Q.7 Calculate force in given frame building with following data: (i) Column size = 375 x 375 mm (ii) Beams size = 300 x 375 mm (iii) Brick wall thickness 150 mm (iv) Floor thickness = 120 mm = (v) Live load on the floor = 4.0 kN/m² (vi) Storey height = 4.0 m each (vii) No. of storeys = 5 y 5@5.0m Plan 2@5.0m [R.T.U. 2017] X
show your step by step solution
Compute the maximum combined loads using the recommended ASDexpressions from the AISC. D = 10,000 lb,W = ;32,000 lb