Assuming that the Watchdog timer is enabled, what is value to be placed in the OPTION_REG to allow the timer to reset the microcontroller every 36 msec? Assume Fosc = 90 KHz.

Q: : For the following datapath and control design: PUA Insn Mem Register File $1 $2 Rwe Rds AL Jop…

A: In order to determine the two possible addresses that can be stored in the PC register when the…

Q: PIT clock i

A: Given : - A programmable interval clock (pit) clock is given and operating frequency is,  f =  24MHz…

Q: When a word of data is Input from the I/O address AAAAH, the state of the control signal which occur…

A: ANSWER: BHE#0, A0=0, M/IO#=1, DT/R#=0, RD#=0, WR#=1, DEN#=0 Explanation Transport High Enable &…

Q: What hex value do you need to put in the Direction register in order to initialize the GPIO pins as…

A: Given: What hex value do you need to put in the Direction register in order to initialize the GPIO…

Q: What is the significance of watchdog timers in many embedded systems?

A: Watchdog Timers is widely used in the computers for automatic correction of the temporary hardware…

Q: Explain the concept of hardware interrupts. What are its advantages over polling? How are timer…

A:

Q: : For the following datapath and control design: PUA Insn Mem Register File $1 $2 Rwe Rdst ALUinB BR…

A: In computer architectures, the PC (Program Counter) register typically stores the address of the…

Q: Use of accelerometer and gyroscope sensor module.Program the controller to read value of this sensor…

A:

Q: What's the best way to connect a Micro SD Card Memory Shield Module, an HC-SR04 ultrasonic sensor,…

A: In this question we have to understand about the ways to connect a Micro SD Card Memory Shield…

Q: In firmware development if I wanted to develop a driver for the SSD1331, what is the thought process…

A: 3. Interacting with SSD1331 via SPI1. Configuring SPITo initiate SPI, configure the clock speed,…

Q: Assume you have two buttons connected to PDO, PD1 generate a PWM signal on PD2 with frequency of 50…

A: equation for 4th order (using X for 'x')(yR' + yR + er' + e'eRs) = 0= (1/2X - y0) * (1/2X - y0) *…

Q: Write a program to get data from port B and send it to port C continuously while an interrupt will…

A: Requirements:Continuously read data from Port B and send it to Port C.Use an interrupt such that a…

Q: How is an external hardware interrupt handled on the INTR pin of the 8086/88?

A: Given: How is an external hardware interrupt handled on the INTR pin of the 8086/88?

Q: er that counts errupt in your p

A: Please use ARM Processor Confagerations!!

Q: Embedded Systems question   Configure the SysTick Timer to generate 2 ms delay utilizing the bus…

A: Systick timer is an application of Microcontroller in Embedded systems

Q: A traffic light PLC program working with a screen will be installed. We will enter and adjust the…

A: A traffic light PLC program working with a screen will be installed. We will enter and adjust the…

Q: Describe the time signal sequence used by 8155 programmable devices when they read or write to an…

A: Below is the solution :

Q: What technique used to eliminate stalls by making data available to active components before it can…

A: Introduction Pipelining: Pipelining is a method for decomposing a sequential process into different…

Q: Explain the following code. What is the purpose of the keyword volatile and why is it necessary:…

A: I  have answer this  question in step 2.

Q: What are the benefits of using watchdog timers in many embedded systems?

A: Introduction An embedded system is a specialized computer system designed to perform dedicated…

Q: So many embedded systems nowadays use built-in watchdog timers; why is this so?

A: Embedded systems are often used in critical applications, such as medical devices, automotive…

Q: What is the need for watchdog timers in so many embedded systems?

A: Watchdog timers provide a method for alerting a system or resetting a processor whose software has…

Q: What logic block writes to a register file? Answer and submit. Select an answer using the up/down…

A: In digital circuit architecture, a register file is a collection of registers that can be read from…

Q: A hardwired electromechanical master control relay (MCR) is normally included as part of the PLC…

A: MCR is the device which is used to remove power from the loads of it necessary.

Q: The method which the processor continually checks the status flags in each module to find which one…

A: The suitable option is (a).Software Polling

Q: How to program the SYSCFG external interrupt configuration registers (SYSCFG_EXTICR) to map EXTI 13…

A: Here we know about the SYSCFG  program for external interrupt configuration registers to map EXTI 13…

Q: What is the need for watchdog timers in so many embedded systems?

A: Please find your answer below in second step:

Q: Overview The purpose of this lab is to control and program the MC8051 Timers of the micro-controller…

A: Assembly code is a low level programming language which is between high level language and machine…

Q: To which register does the control unit look to determine whether the rt or rd register should serve…

A: Introduction: The control unit (CU) is a component of the central processing unit (CPU) of a…

Q: ?The entire program will be run every scan in the PLC cycle

A: Given:

Q: 11. What Binary value should be loaded in the TMOD register of 8051 Microcontroller to use the…

A: According to the information given:- We have to explain Binary value should be loaded in the TMOD…