Answered: Assuming all terminals are rated 75… | bartleby

Related questions

Question

Assuming all terminals are rated 75 degrees C, what is the maximum size overcurrent protective device (fuse or breaker) that the NEC allows for protecting the following copper THHN/THWN conductors:

Four #8 wires run in a dry/damp location with an ambient temperature of 36 degrees C

Expert Solution

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

A thermistor is a type of resistor whose resistance varies significantly with temperature, more than in standard resistors. Thermistors are widely used as inrush current limiter, temperature sensors (NTC type typically), self-resetting overcurrent protectors, and self-regulating heating elements. Assume that the relation between resistance (R) in ohms and temperature (T) in Celsius of the thermistor is given by: R=(1+0.3T)/2 By using error propagation formula, calculate the temperature and associated error if R = 15 ± 1 Ω.
A battery with a 0.133 02 internal resistance supplies 16.7 W of total power with a 8.61 V terminal voltage. Determine the current I (in A) and the power PR (in W) delivered to the load resistor. (Enter your answers to at least three significant figures.) | HINT (a) the current I (b) the power PR ХА W
00-gauge copper wire has a diameter of 9.266 mm. Calculate the power loss in a kilometer of such wire when it carries 1.00×102 A .
P Question 21
The largest operating wind La generator in the world has a rotor diameter of almost 100m. This nits generator can deliver 3 3.1 MW of power. Suppose you connect adl 3.0 K resistor, a 4.0K resistor, and a 5.ok resistor in parallel- klhat potential difference must be applied across these resistors) in order to dissipate power w 1.00 percent of the Jock equal to power provided by the generator? Show all working step-by-step gat2 word stz
Two copper wires have the same volume, but wire 2 is 25 % longer than wire 1. The ratio of the resistances of the two wires R2/R1 is ( Hint: radius will not be same) 0.82 0.91 1.2 1.56 1.0
A 2.00-nF capacitor with an initial charge of 5.99 µC is discharged through a 2.42-k resistor. (a) Calculate the current in the resistor 9.00 µs after the resistor is connected across the terminals of the capacitor. (Let the positive direction of the current be define dQ such that dt > 0.) 192.757 X This is the correct magnitude of the current mA (b) What charge remains on the capacitor after 8.00 µs? 9.329e-7 X What is the equation describing the time dependence of the charge on a capacitor that is being discharged in an RC circuit? µC (c) What is the (magnitude of the) maximum current in the resistor? 1.237 A
Problem 5: A current of I- 2.6 A passes through the circuit shown, where R- 65 3R 5R V) 2R 6R 2R 7R 5R 10R Otheexpertta.com Part (a) In terms of R, I, and numeric values, write an expression for the voltage of the · source, V. Part (b) What is the voltage, V in volts? tan( sin() cotanO a acos cosh0t cosO asin() acotan 4 5 6 sinh() cotanhO *1 23 0 tanh0c O Degrees O Radians CLEAR BACKSPACE
Please asnwer all parts of the one problem: Consider the three resistors R1 = 17 Ω, R2 = 41 Ω, and R3 = 71 Ω in the configuration shown in the figure. A potential difference ΔV = 4.5 V is applied between A and B. Part (a) Calculate the numerical value of the total resistance R of this circuit, in ohms. Part (b) Calculate the numerical value of the current I traveling from A to B, in amperes. Part (c) Calculate the numerical value of I2 traveling through the resistor R2, in amperes. Part (d) Calculate the numerical value of I3 traveling through the resistor R3, in amperes.