Assume that the initial energy stored in the inductors of both figures is zero. Suppose that L₁ = 8 mH and L2 = 16 μΗ . Figure 12 mH 24 mH 8 mH 10 mH m 20 mH 30 mH 1 of 2 315 mH Part B Find the equivalent inductance of (Figure 2) with respect to the terminals a, b. Express your answer to three significant figures and include the appropriate units. Lab= 13.5 Submit Previous Answers Request Answer X Incorrect; Try Again mH Provide Feedback ?

Assume that the initial energy stored in the inductors of both figures is zero. Suppose that L₁ = 8 mH and L2 = 16 μΗ . Figure 12 mH 24 mH 8 mH 10 mH m 20 mH 30 mH 1 of 2 315 mH Part B Find the equivalent inductance of (Figure 2) with respect to the terminals a, b. Express your answer to three significant figures and include the appropriate units. Lab= 13.5 Submit Previous Answers Request Answer X Incorrect; Try Again mH Provide Feedback ?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A string of suspension consists of four (4) units. The Voltage between each pin and earth is 0.12 of the Self-Capacitance of the unit. The Voltage between the Line Conductor and earth is 135KV. Find the Voltage distribution across each unit and the String Efficiency
The loads on a 300-meter ring distributor are depicted in figure 2.1 (a), where the distances are given in metres. Each conductor has a resistance of 0.20 per 1,000 metres, and the loads that are tapped off at points B, C, and D are as shown in the diagram. Determine the voltages at B, C, and D given that the distributor is fed at point A. 50 A 70 1 240 V A (a) 60 B 70 A 100 A 80 50 A 91A D T 41 A 220 V A (b) 129 A B 100 A 729 A 70 A
A) Explain earthing and its importance in electrical installation. BÍ With a help of a labelled diagram a single phase supply, differentiate between TN-S earthing system and TN-C-S system. C Calculate the earthing resistance of an electrode given its length is 4 dm and its radius of 1 cm if the resistivity of the soil is 50 ohms. D) From the result obtained in the question 2(C), calculate the earth resistance when two similar electrodes are in parallel. Explain your answers.
14. For a power plant with two units, the weekly load is 1200 MW. The coal consumption (tons/hour) for each unit is Q₁ 16+.3P₁ tons/hours Q2-25+.4P₂ tons/h The total coal available to the plant is limited to 90,000 tons/week. If the linear cost curves are given as C₁=495+11P₁ $/hour, C₂-760+10P₂ $/hour And generation by each unit is limited to 150 ≤ P, ≤ 600MW Determine the values of P₁ and P₂ for minimizing the cost of power generation. 15. Use LP to determine economic dispatch if C₁ = 5+ 3P₁, C₂ = 7+6P2, C3 = 8 + 9P3 50 P₁ < 150 MW and PD=210 MW If the line flow P12= .3P₁ + .4P₂ + .1P3, also determine P₁, P₂ and P3 so that P₁2 is limited to 70 MW. 1 4 400 ≤ P₂ ≤1000MW H 2 3
Q2/B: A grading string of four insulators has a uniform voltage across each disc. The capacitance of each pin to earth is C. The capacitance of the top unit is 5 C as shown.(a) Calculate the capacitance of the remaining discs, (b) If the voltages of units one and two are 60% and 40% of line voltage.,Calculate other voltages and string efficiency.
21. A piece of wire that is one mil in diameter and one foot long is one mil-foot. Select one: TRUE FALSE
21 Balance is obtained in a DC potentiometer at a length of 71 cm when using a standard cell of 53.2 volts. Calculate the EMF of a dry cell if balance is obtained with a length of 20 cm. a. 0.07 b. 14.99 c. 0.01 d. 188.86
MECT361 Mechatronics Components and Instrumentation PLEASE GIVE ME THE short answer and wite it by keyword thanks
Find the current l4 for the figure shown below. 100A 40A 12 I1 80A 13 15 10A 14? a. 100A O b. 400A c. 200A O d. 150A