Assume an annual available energy of 1200 Kwh/m2. The system rating peak is 50 Kw. The annual energy yield is 51000 Kwh. Find kwh 1) The Final yield Y [- Kw 2) The Performance ratio [%] 3) Given the Monthly values of final yield (Yf), reference yield (YR), and array yield (YA for one year, plot the monthly Performance ratio in percent for the whole year. YF YR YA 8.00

Assume an annual available energy of 1200 Kwh/m2. The system rating peak is 50 Kw. The annual energy yield is 51000 Kwh. Find kwh 1) The Final yield Y [- Kw 2) The Performance ratio [%] 3) Given the Monthly values of final yield (Yf), reference yield (YR), and array yield (YA for one year, plot the monthly Performance ratio in percent for the whole year. YF YR YA 8.00

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Either solve all or don't
1 A resistance of 20ohms, an inductor of 0.2H and a capacitance of 100uF are connected in series across 220V 50HZ.Determine a)impedance, b)current, c) voltage across R,L and C, d) power in watts and VA, e)p.f. and angle of lag, f) draw the circuit and diagram.
Q.5: Correct any five sentences using suitable scientific phrases. 1 TAMAGE INTE- 2. 3. nic The Z-parameters representation of any two-port network is called current equations. 5. Mutual impedance occur due to the electric field in coils. 6/ The reading of 2-wattmeter give the power in the two phases.
ASAP 20 minutes left
A 55000 kW thermal plant of National Power Corporation delivers an annual output of 238000000 kw-hr with a peak load of 44 MW. What is the capacity factor? a. 49.4% b. 42.4 % c. 48.2% d. 44.6%The Answer is not 63.74.
74956 non-reactive resjstof value 474 0 is connected in series with a capacitor. The combined circuit is connected to a 230 V, 50 Hz supply. If the ippeylihek bPhe combined circuit is 500 (2, calculate: a)beATue of the capacitor. b) the current in the circuit. c) the reactance of the capacitor.
Question-2 Can you throw the emergency solution? I would appreciate it if you write legibly.
A power station has a maximum demand of 13590 kW. The annual load factor is 60% and plant capacity factor is 50%. Determine the reserve capacity of the plant.
The graph of the vs sign applied to the circuit in the figure is given above. The switch works ideally in the circuit Switch; When the applied input signal is positive, it becomes closed. Current flows through it) In the applied input signal, Vp = 12V, R = 10ohm, T = lms. According to this; a) Find the mean and rms values of the output voltage? b) Find the average input power and output power and calculate its efficiency. c) If we consider that there is a voltage drop of 1V on the switch; c.1) Calculate the average and rms values of the output voltage, c.2) Average input power and output power c.3) Efficiency.
Do it your own Handwriting
Consider the situation shown in (Figure 1). A 1000-V-rms source delivers power to a load. The load consumes 140 kW with a power factor of 55 percent lagging. Time remaining: 00:07:30 Electrical Engineering Consider the situation shown in (Figure 1). A 1000-V-rms source delivers power to a load. The load consumes 140 kW with a power factor of 55 percent lagging. 1- Find the phasor II, assuming that the capacitor is not connected to the circuit. Enter your answer using polar notation. Express argument in degrees. 2-Find the value of the capacitance that must be connected in parallel with the load to achieve a power factor of 100 percent. Express your answer to three significant figures and include the appropriate units. 3-Usually, power-systems engineers rate capacitances used for power-factor correction in terms of their reactive power rating. What is the rating of this capacitance in kVAR? Express your answer using three significant figures. 4-Assuming that this…