Assume a tank in the shape of an inverted cone, with height 12ft and base radius 4 ft. The tank is full to start with, and water is pumped over the upper edge of the tank until the height of the water remaining in the tank is 4 ft. How much work is required to pump out that amount of water? Use pg = 62.4lbf/ft³ O 5650π ft-lbf O 15650 ft-lbf O 20650 ft-lbf O 10650 ft-lbf

Assume a tank in the shape of an inverted cone, with height 12ft and base radius 4 ft. The tank is full to start with, and water is pumped over the upper edge of the tank until the height of the water remaining in the tank is 4 ft. How much work is required to pump out that amount of water? Use pg = 62.4lbf/ft³ O 5650π ft-lbf O 15650 ft-lbf O 20650 ft-lbf O 10650 ft-lbf

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: How much work (in ft-lb) is done when 10 ft of an air is initially at a pressure of 1 atm and a…

A: 0 is the correct answer. Since the volume of cylinder remains constant. It is an isochoric process.…

Q: Three pipes are connected in parallel, The difference in heads in each pipe is 40 m. Pipes Diameter…

Q: A cylindrical object 82mm diameter, 155mm height and a mass of 611g, is placed in the tank, which…

Q: The following data were recorded when a centrifugal pump worked at its maximum efficiency: Q = 40…

A: Given a centrifugal pump worked at its maximum efficiency. Q=40 lps. Manometric head, Hm=25 m Speed,…

Q: A tank is 11 meters long, 6 meters wide, and 4 meters high. The tank is filled with gasoline, which…

A: Density of liquid = 750 kg/m3 g = 9.8 m/s2 Determine a. Hydrostatic pressure on the bottom of the…

Q: The tank shown below has an orifice at the bottom. Use the Bernoulli equation to find the velocity…

A: According to given data The tank shown below has an orifice at the bottom. Use the Bernoulli…

Q: Consider a hydraulic jack being used in a car repair shop, as in the figure. The pistons have an…

Q: From the figure shown, the tank contains oil having s specific gravity of 0.80. Oil flows at a…

Q: A diesel tank is kept by an industrial facility to power their equipment. To effectively distribute…

A: The density of diesel, ρd=854Kgm3The height of tank, L=2.77mThe diameter of pipe, d=0.12mThe…

Q: In the figure shown, determine the weight that can be carried by the 1.5 kN force acting on the…

A: To determine the weight that the piston can carry. Given, Load acting on the piston (F) = 1.5 kN…

Q: 12. A liter of water weighs about 97,500 dynes, what is its mass in kilograms?.

Q: 13. For the reservoir-pipe system shown in the figure given below, by considering the liquid as…

A: Solution:

Q: FIGURE 3-100E A crane is used to lower weights into a lake for an underwater construction project.…

Q: SITUATION 1. A cylindrical tank, 0.Sm in diameter containa 3 different types of fuids as shown. If…

Q: A nozzle of inner radius 1.04 mm is connected to a hose of inner radius 8.55 mm. The nozzle shoots…

Q: KWhich one of the following is the unit of pressure? a) N b) N/m c) N/m² d) N/m3

A: Pressure is defined as the ratio of force per unit area . Pressure =ForceAreaForce unit is Newton…

Q: Pipe Length Diameter 1 947mm 250mm 583mm 275mm 3. 1026mm 180mm

Q: چسا W Jh Water Scale The figure shows a water tank that weighs 920 N when empty, and contains 1.1…

A: WT (weight of tank) = 11711 N

Q: The mass of fluid is 0.371slug, its density is 30lb/ft3 and g = 32.7 ft/s2 . Find the total volume…

Q: 2.80 m Air oil, s = 0.80 B

Q: Topics: Fundamental of fluid flow In Lake Geneva (Switzerland), there is a water jet (called the…

A: step 1-

Q: A 1-m³ volume of water is contained in a rigid container. Estimate the change in the volume of the…

A: Given: Volume of water in rigid container, V = 1 m3 Pressure applied by the piston = 46 Mpa = 46 *…

Q: As shown in the figure, a pump draws water from reservoir A (El 10m) and lifts it to reservoir B (El…

A: Given two reservoir problem with a pump supplying head. In order to calculate the pressure head at…

Q: Three pipes are connected in parallel. The difference in heads in each pipe is 40 m. Pipes Diameter…

Q: A vessel containing liquid, S = 1.5, is rotated about a vertical axis. The pressure at one point…

Q: Length of Pipe 3 = 210 m Length of Pipe 4 = 450 m *Pipe 2 and Pipe 3 are parallel Diameter…

Q: Convert a flow of water flowing in a pipe 410 Liters/ hr into kg/hr, m³/min discharge in kg/hr…

A: 1 Liter per hour is equal to 0.74 kilogram per hourSo,410 Litershour=303.12 kghour

Q: A cylindrical vessel with closed bottom and open top is 0.9 m in diameter. What is the rotational…

A: Given- Dia of open top=0.9 mrise=0.5 mbottom dia=0.4 mg=10 m/s2 Rotational speed needs to be find…

Q: Water flows through a Venturi meter, as shown in the figure. The pressures of the water at locations…

A: To find out the difference in pressure between a and b.

Q: Two springs support two identical blocks as shown. Ifs 1.2m, calculate the weight of each block. Im…

A: Given:- Two identical blocks are supported by two spring The stiffness coefficient of both the…

Q: Turbomachinery Question 2: A single-acting reciprocating pump has a 15 cm piston with a crank radius…

A: Given data- A single-acting reciprocating pump- Piston diameter d=15 cm=0.15 m, Crank radius r=15…

Q: length of 10 m, friction coefficient of 0.025, and local coefficient of 2; discharge pipe has:…

A: Given:- distance between water levels in the two tanks is 25 m; pump capacity is 10 m3/h; suction…

Q: 4. A large tank has a height of 5.0 m and an area (in plan) of X m2. It has a small outlet (orifice)…

Q: 180 kg M

Q: A 1-m³ volume of water is contained in a rigid container. Estimate the change in the volume of the…

Q: A cylindrical object 82mm diameter, 155mm height and a mass of 611g, is placed in the tank, which…

Q: A 2 m diameter cylinder rotates at 1800 rpm in an air stream (p=1226 kg/m³) of 25 m/sec. Estimate…

Concept explainers

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.

Question

Assume a tank in the shape of an inverted cone, with height 12ft and base radius 4 ft. The tank is full to start with, and water is pumped
over the upper edge of the tank until the height of the water remaining in the tank is 4 ft. How much work is required to pump out that
amount of water? Use pg = 62.4lbf/ft³
5650π ft-lbf
15650 ft-lbf
20650π ft-lbf
10650π ft-lbf

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A fluid storage tank is fixed to the wall as shown in the figure. Considering the unit width (into the page) of the container, a) Determine the reaction at the fixed support. Neglect the thickness and weight of the container. h (oil) = 0.53 m h (water) = 1.41 m h (mercury) = 0.71 m L = 3.0625 m
ı need solution
9. A tank as shown in figure below compose of hemispherical at the top, cylinder at the middle and cone at the bottom is contain of full water, A 100 mm 4 orifice located at the bottom (C = 0.62), compute for; A) Time to drop the water from 7m to 4 m B) Time to empty the half of water in the tank C) Time to empty the whole tank 4mp 2 m 3 m 2 m
A 1-m³ volume of water is contained in a rigid container. Estimate the change in the volume of the water when a piston applies a pressure of 46 MPa. 0.0219 m³
Find the pressure magnitude in the Gasoline Pipe at the right side of the figure. Specific weight of water is 9.81 kN/m3 and specific weight of air is negligible. Oil SG= 0.79 Pgage = 376 kPa Gasoline SG = 0.70 Air 45 cm 50 cm Pipe 22 cm † 10 cm Water `Mercury SG= 13.6
Use the following given values to solve problems, unless otherwise stated. Ywater = 9790 N/m³ = 62.4 lbf/ft°; g = 9.81 m/s? = 32.2 ft/s²; 1 hp = 550 lbf-ft/s = 746 Watts Problem-1 Water is pumped from the large tank through a uniform diameter pipe (d = 3 in.) and exits as a free jet (refer figure-a). The plot of the flowrate (Q) versus pump-head (hp) is a straight-line graph that passes through points (3, 16) as shown in figure-b. If the pipe friction head loss is, hf = 7V:/2g, where V is the average fluid velocity in the pipe, find a) the equation that relates hp and Q; b) flowrate and c) If the pump is 75% efficient, what horsepower is needed to drive it? Assume steady, incompressible flow. Ignore kinetic energy correction factor (a). 12 ft Pump %3D (a) 16 3. Q, ft°ls (b) dy
I need the answer as soon as possible
A nozzle of inner radius 1.04 mm is connected to a hose of inner radius 8.83 mm. The nozzle shoots out water moving at 25.0 m/s. 1. Required information At what speed is the water in the hose moving? cm/s Required information What is the mass flow rate? g/s 2.
A tank is filled with water up to a height of 0.9 m and has an orifice of diameter 15 mm at the bottom. If the air is being pumped into the upper part of the tank, determine the pressure required for a discharge of 1.5 liters/s through the orifice. Take Ca = 0.62.