Assignment-2 Q1. Derive an expression for the input impedance of the equivalent network for the passive component shown below. Find the input impedance at 500 MHz. Estimate also analytically the resonance frequency of the component. L R 15 nH 0.5 2 1 pF

Q: What is the difference between continuous wave and pulse wave transducers? This is for DMS 101…

A: The difference between the continuous wave and pulse wave transducers is explained by the following…

Q: In RG 59 coaxial cable RG term represents

A:

Q: Give two examples each of electrical impedance cell counting machines and light scatter cell…

A: Give two examples each of electrical impedance cell counting machines and light scatter cell…

Q: loop operation is followed in SMPS operation.

A: Open loop

Q: The signal is sampled with sampling time interval of 5 seconds then the time period of the message…

A: The sampling frequency should be at least twice the message signal frequency. fs≥2fm The sampling…

Q: In a transistor....... Ic = lE+IB IE= IC - IB E = IC + IB B = Ic+IE

A: Lets consider the NPN Bipolar junction transistor circuit,

Q: Counter Output Question. input. 60 Hz rrr MOD-6 Counter Decade Counter Output (Hz)

A:

Q: Which one of the following is the correct implementation of this multiplexer?

A:

Q: Systematic errors are reading error O instrument calibration O unsuitable environment all of these O…

A: The explanation is as follows.

Q: The most common standard electronic current transmission signals range fron to mA.

A: The most common standard signal for electronic transmission is 4 to 20 mA.

Q: -By Michelson interferometer we can determine

A: Given   We need to enumerate what can be determined by using Michelson interferometer. Please find…

Q: Define signal generator and list the requirements of laboratory type signal generator and raw block…

A:

Q: Differentiate the types of pulse modulation techiniques

A: Modulation- Modulation is the process of changing the characteristics of the carrier signal in…

Q: The data select inputs of 1 to 64 De-Multiplexer is

A: Given :    Demultiplexer is a device which is series to parallel converter.     In case of…

Q: Noise caused by random fluctuation of electrons in an electronic device is

A: In the electronic devices noise unwanted signal that is superimposed on the input signal and then…

Q: Determine the oscillator frequecny and typr of oscillator of the given circuit. L= 10 µH C,=2pF C2 =…

A: The feedback circuit give a part of output signal back to input signal. When output signal is…

Q: Draw the circuit of a Mod 5 synchronous counter that count the states 010, 011,100,101 and 110

A:

Q: A JFET data sheet specifies VGS(off) = –6 V and IDSS = 8 mA. The value of ID when VGS = –3 V is…

A: Brief description: In the above given question they want to know the saturation current for the…

Q: If a 100 Hz sinusoidal signal is sampled at the rates of 140 Hz, 90 Hz, and 30 Hz, then the aliased…

A: Given information is shown below:

Q: If the value of a APC 0.44 find the value of a APS need soon

A: Given: APC OF AN ECONOMY IS  0.44  CALCULATE :  APS

Q: 2. A 500 Hz modulating voltage produces a frequency deviation of 2.25 kHz. What is the modulation…

A:

Q: Calculate Vo andı I . Vcc=20 V , diodes are 0.7 V. Resistors are 5kΩ.

A: For the given circuit the value of the voltage Vo and the current I needs to be calculated and the…

Q: or op-amp wien bridge oscillator if the oscillator stops after few cycles then the cause is?

A: An Op-amp Wein Bridge oscillator is shown below: It is one of the simplest sine wave oscillators.…

Q: What is the required input voltage at AREF pin in Arduino UNO to have LSB voltage resolution of 1.47…

A: Given, Resolution of Arduino Uno is 1.47 mV. The Arduino Uno ADC is of 10 bit resolutions.

Q: What is set up time. What would be the frequency of a ring oscillator implemented using three NOT…

A:

Q: The information carried by carrier of AM -DSB-SC signal is greater than USB zero equal to USB and…

A:

Q: Kindly assist to check if the new design I made with the insertion of this multiplexer works.

A: According to the question, we need to check the design shown below

Q: In CRO, the time/cm knob indicates scale on vertical axis. Select one: O True O False

A: A cathode-ray oscilloscope (CRO) is a type of electrical instrument which is used for showing the…

Q: Convert (5432)base10 to base8

A: Given data, 543210=8

Q: 2- Find and plot the output signal of the system as shown: 4 3.5 2.5 3 2 2.5 1.5 2 1.5 1 0.5 0.5 0.5…

A:

Q: Draw the expected signal waveform across R1. Draw the expected signal waveform across R2. What is…

A: Expected signal waveform across R1.

Q: Represent the fallowing cet Diogram into blockDiagram R

A: Basic electrical circuit problem.. Below is the solution..

Q: The contents of the designated register pair are decremented by 1 and the result is stored in the…

A:

Q: (d) State any three types of active filters.

A: The three types of active filters are,   Active low pass filter Active high pass filter Active band…

Q: The most commonly used demodulation technique for FSK uses circuit.

A: According to the question we have to discuss about the most commonly used demodulation technique for…

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.