zain IQAsiacellIn the experiment of finding theparameters of synchronous machine,the ac value of the armatureresistance equal the Radc multipliedby *1.21.251.11.35In the experiment of finding theparameters of synchronous machine,to measure the armature resistance,the stator windings areconnected in parallel and ac voltageapplied to themconnected in series and a dcvoltage applied to them.connected in series and ac voltageapplied to them.connected in parallel and dc voltageapplied to themالعربيةالإنجليزية

As per Bartleby guidelines we are allowed to solve only one question,please ask the rest again.

Answered: Asiacell In the experiment of finding…

Asiacell In the experiment of finding the parameters of synchronous machine, the ac value of the armature resistance equal the Radc multiplied by *

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 2 pole wave wound dc generator has 44 slots, each slot having 20 conductors. The flux/pole is 0.018 weber. At what speed the armature be rotated to get an induced emf of 220 V. What will be the induced emf developed if the armature winding is lap connected and runs at the same speed. Speed Generated Emf when lap connected
A 35-ohm diverter resistance is shunted across the series field of a DC series generator is supplying a current of 6 A to a series lighting system through a feeder of total resistance, 1.25 ohm. The terminal voltage is 2,300 V. The armature and series field resistances are respectively 18 and 15 ohms respectively. Determine the power developed in the armature of the generator?
Consider the following statements regarding the design of the distributed armature winding in a three-phasealternator:1. It reduces the phase belt harmonics.2. It increases utilization of armature iron and copper.3. It increases rigidity and mechanical strength of the winding.4. It reduces copper in the overhand of the winding. Which of the statements are correct? a. 1,3 and 4b. 2,3 and 4c. 1,2 and 3d. 1,2,3 and 4
A short shunt compound generator delivers 150A at a terminal voltage is 230V. The shunt field current is 2.5A. The resistances of the armature, series field and diverter are 0.032-ohm, 0.015 ohm and 0.03 ohm, respectively. Calculate the electrical efficiency of the generator at this load.
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: AC MACHINES Answer the following questions (A, B and C) depending on the topic. 1. ALTERNATORS A. Why is it necessary to maintain the speed of an alternator at all times and how do they control the speed of an alternator when in operation? B. Distinguish between half-coiled and full-coiled armature windings in alternators. C. Why are fractional pitch windings generally used in alternators?
A 8 pole wave wound dc shunt generator runs at a speed of 900 rpm, has an armature and shunt field resistance of 0.7 N and 300 N respectively. The armature has 960 conductors and flux per pole is 0.057 Weber. If the lamp load connected has a resistance of 60 2, determine (i) Generated EMF, (ii) Total Resistance, (iii) Armature Current, (iv) Terminal Voltage. Generated EME (Eg) Total Resistance (Rt) Armature Current (la) Terminal Voltage (V)
A DC series generator is supplying a current of 5A to a series lighting system through a feeder ofto total resistance, 1.0 ohm. The terminal voltage is 2500 V. The armature and series fieldresistances are respectively 18 and 15 ohms respectively. A 30-ohm diverter resistance isshunted across the series field. Determine the power developed in the armature of thegenerator?
(a) A single phase distributed winding carries alternating current. Show that the time maximum of the peak mmf for a P pole machine is given by 4 N V21 Fipm -K ph ATs per pole P
READ THE PROBLEM AND JUST DRAW CIRCUIT DIAGRAM. NO NEED TO SOLVE ANYTHING. A short shunt compound generator delivers 150A at a terminal voltage is 230V.The shunt field current is 2.5A. The resistances of the armature, series field and diverterare 0.032 ohm, 0.015 ohm and 0.03 ohm respectively. Calculate the electrical efficiencyof the generator at this load. Modify the circuit diagram on the picture based on the problem. Answer: 95.7%
Under load in DC machines, the armature current will cause: a. Compensating Windings O b. Increase in the main flux Oc Armature Reaction O d. Interpoles
. A 20 kW compound generator works on full load with terminal voltage of 250 V. The armature, series, and shunt windings have resistances of 0.05-ohm, 0.025 ohm, and 100 ohms, respectively. If the machine is connected short shunt, the emf generated is nearest to. (Our subject is Electrical Machines 1 ) (I need a clear answer and solution. Thank you so much)
A thicker wire is used in the DC series field winding than DC shunt field winding in DC machines. * O because it carries the load current. O to prevent mechanical vibrations. O to provide strength. O to produce large flux. The speed of a DC motor can be changed by varying - armature resistance circuit O flux per pole O voltage source O all of above