As shown in the PV diagram below, the cycle goes in the order of states A-B-C-D, and the system is one mole of a monatomic idealgas. The processes between each state are labelled as 1 through 4.Rank the work done by the gas in each process from most negative to most positive (most negative listed first, most positive listedlast).1AВ4Po3Po42PoРоDVo 2Vo 3Vo 4Vo4, 3, 2, 1O 1, 2, 3, 4O 1, 2=4, 33, 2=4, 1O 2=4, 1=3

Correct ans is 3,2=4,1 In process 3 workdone is negative dur to change in volume is negative In…

Answered: As shown in the PV diagram below, the…

Similar questions

Please provide solution, thanks.
The thermodynamic cycle of a heat engine using ideal helium gas is shown in the P-V diagram. The ratio of heat capacities y (also called ratio of specific heats) is the ratio of the heat capacity at constant pressure Cp to the heat capacity at constant volume Cy. For ideal helium gas, y = 1.67. Select the stage that is paired correctly with the process it represents in the P-V diagram. 1-2: adiabatic process O2-3: isochoric process 3-4: isothermal process 4-1: isobaric process p (kPa) 0.8 0.6- 0.4- 0.2 0.0 2 0.2 0.4 0.6 1 0.8 V(m³) 1.0
Consider a process that uses n moles of a monatomic ideal gas operating through a Carnot cycle. The initial temperature and pressure of the gas are T1 and P1, respectively. Consider steps 1 → 2, 2 → 3, 3 → 4, and 4 → 1. a. In the adiabatic heating, the temperature of the gas is doubled. Write an expression for the volume V3 after this step in terms of V1. b. Write an expression for the volume V4 in terms of V1.
One mole of an ideal gas is used as the working substance of an engine operating in the cycle shown in the figure below. BC and DA processes are reversible adiabatic.a) Is the gas monoatomic, diatomic or triatomic?b) What is the efficiency and engine?
A monatomic gas is take through a cycle from A to B to C and back to A. At A the pressure is 100,000 pa, the volume is 4.0 liters, and the temperature is 300K. The gas is compressed adiabatically until the volume is 1.0 liters (at B). How much energy was given to or removed from the gas during the adiabatic process?
A certain gasoline engine is modeled as a monatomic ideal gas undergoing an Otto cycle, represented by the p-V diagram shown in the figure. The initial pressure, volume, and temperature are p1 = 1.05 × 105 Pa, V1 = 0.035 m3, and T1 = 290 K, respectively. a)The first step in the Otto cycle is adiabatic compression. Enter an expression for the work performed on the gas during the first step, in terms of V1, V2, and p1. b) Calculate the temperature of the gas, in kelvins, at the end of the first step. c)The fourth and last step in the Otto cycle is isochoric cooling to the initial conditions. Find the amount of heat, in joules, that is discharged by the gas during the fourth step.
An ideal gas undergoes the thermodynamic process shown in the ??PV diagram in the figure. Determine whether each of the values (a) Δ?ΔU, (b) ?W, (c) ?Q for the gas is positive, negative, or zero. (Note that ?W is the work done ??on the gas.) Hint: First use the ideal gas law to find the initial and final temperatures in terms of ?0P0 and ?0V0 and determine if the final temperature is greater than, less than, or equal to the initial temperature. (a) ΔU A.+ B.- C.0 (b) W A.+ B.- C.0 (c) Q A.+ B.- C.0
You would like to raise the temperature of an ideal gas from 295 K to 960 K in an adiabatic process. a)What compression ratio will do the job for a monatomic gas? b)What compression ratio will do the job for a diatomic gas?